manualshive.com logo in svg

Keba KeDrive D3-DA BG3, Руководство по эксплуатации

Поделиться
Скачать
Keba KeDrive D3-DA BG3 Скачать руководство пользователя страница 9

9

1  Safety

Operation Manual KeDrive D3-DA BG3 and BG4 

1804.200B.1-01    Date: 03/2023

Safety

2 

Safety

2.1  Overview

Our devices are state-of-the-art and comply with recognised safety regulations, 
nevertheless hazards can arise. In this chapter:

 

y

We provide information about residual risks and hazards that can emanate from 
our devices if used as intended.

 

y

We warn about the foreseeable misuse of our devices.

 

y

We refer to the necessary care and measures to be taken to prevent risks.

2.2  Measures for your safety

NOTE

Your device is only allowed to be installed and placed in operation taking into 
account the documentation for the related device family!

Our devices are quick and safe to operate. For your own safety and for the safe function 
of your machine, please be sure to observe the following points:

1.

Follow safety instructions for the devices

: 

Follow all safety instructions and warnings in the entire documentation related to the device range.

2.

Electrical drives are dangerous:

•  Due to electrical voltages up to 480 V AC and up to 800 V DC
•  Even 10 min. after switching off the mains supply, dangerously high voltages of ≥50 V may still 

be present (capacitor charge). Therefore check there is no electrical power in the device! See 

also the warning label on the front panel on the device.

•  Rotating parts
•  Automatically starting drives.
•  Hot components and surfaces

3.

Protection against magnetic and/or electromagnetic fields during 

installation and operation.

Persons fitted with heart pacemakers, metallic implants or hearing aids, etc. must not be allowed 

access to the following areas:

•  Areas in the immediate vicinity of electrical equipment!
•  Areas where electronic components and drive controllers are installed, 

repaired and operated!

•  Areas where motors are installed, repaired and operated! 

Motors with permanent magnets pose particular hazards.

4.

During installation observe the following:

•  Comply with connection conditions and technical data as per the documentation and the rating 

plate!

•  Comply with standards and directives on electrical installation, such as cable cross-section, 

shielding, etc.!

•  Do not touch electronic components or contacts! 

Electrostatic discharge can harm people and destroy components!

•  Take protection measures and use protection devices as per the applicable regulations  

(e.g. EN 60204 or EN 61800-5-1)!

•  Take protection measures against electric shock according to IEC 60364-4-41:2005/AMD1:- 

section 411.3. As a protection measure, use additional protective equipotential bonding as 

described in appendix D of IEC 60364-4-41. 

•  Take "device earthing" protection measure!

5.

Ambient conditions

•  Pay attention to the information about the transport, storage and correct operation of the 

devices stated in the operation manual in "A Appendix". 

Содержание KeDrive D3-DA BG3





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды