manualshive.com logo in svg

Keba KeDrive D3-DA BG3, Руководство по эксплуатации

Поделиться
Скачать
Keba KeDrive D3-DA BG3 Скачать руководство пользователя страница 54

54

1  Commissioning

Operation Manual KeDrive D3-DA BG3 and BG4 

1804.200B.1-01    Date: 03/2023

Commissioning

5.1.3 

Procedure for activating the service/diagnostics mode:

NOTE: 

The function described in the following is available on KeDrive D3-DA axis 
controllers from firmware version V2.20. The service and diagnostics mode is 
activated for all axes in the axis group.

The Ethernet interfaces "X40A ECAT IN" and "X40B ECAT OUT" on the KeDrive D3-DA 
axis controller are in the EtherCAT® operation mode by default after switching on for the 
first time.

So that via this interface with the aid of a PC with KeStudio DriveManager installed 
it is possible to establish a connection to the axis controllers also without control, 
the EtherCAT® interfaces in the axis controllers must be switched to the service and 
diagnostics mode.

Take the following steps to switch over the EtherCAT® interface:

1. 

Identify first axis controller after the supply unit, expansion or capacitance module.

NOTE:

It is necessary to identify the first axis controller (cross-communication master) 
on the right side of the power supply within the cross-communication to 
activate the service and diagnostics mode. Depending on the combination 
with or without expansion or capacitance module and the required number of 
axes, the cross-communication may be interrupted at an expansion module. 
In this situation the next axis controller after the expansion module is a new 
cross-communication master (CCMaster) and opens a new cross-commu-
nication group. Service and diagnostics mode must then be switched on 
separately for this cross-communication group. 

1

3

4

2

8

6

7

5

CC-Master

X40A

X40B

X40A

X40B

X40A

X40B

X40A

X40B

X40A

X40B

X40A

X40B

X40A

X40B

Axis group with one supply unit and maximum of 8 additional bus users --> one cross-communication group
1: Controller | 

2: Supply unit | 

3: Capacitance module | 

4: Axis controller (CCMaster) 

5: Axis controller |  6: Expansion module |  7: Axis controller | 

8: Axis controller

Note:

The cross-communication is via the 8-core Ethernet cables that are included with the modules. An axis group 

(cross-communication group) is shown in this figure. 

Figure 5.2  Cross-Communication (CC) 

Содержание KeDrive D3-DA BG3





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды