Keba D3DP 3 Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 82

Keba D3DP 3 Series Скачать руководство пользователя страница 17

D3DP 3xx/x

Safety notes

Project engineering manual V1.00

17

© KEBA

2.3

Safety instructions for personal safety

WARNING!

Danger of personal injury due to electric shock!

●

Cutoff module from power supply during installation and service. If
theD3DP 3xx/x is supplied by a D3DP 3xx/x whose both supply termi
nals (Line IN and Line IN Aux) must be separated from power (e.g. via
switching a joint main switch mechanism).

●

If the D3DP 3xx/x is supplied by a D3DP 3xx/x you have to wait up to 3
minutes after switchingoff until no more dangerous residual voltage is at
the intermediate circuit. Only after verification of absence of voltage the
supply rails may be opened and the remaining covers can be opened.

●

Supply the control with the D3DP 3xx/x or exclusively from power
sources that have a protective low voltage (e.g. SELV or PELV accord
ing to EN 611312).

●

Protective low voltage circuits must always be installed safely insulated
separated from circuits with dangerous voltage.

WARNING!

Dangerous voltage may be applied to the device, even if the device does
not emit any visual or audible signals/indications!

CAUTION!

Protection against magnetic and/or electromagnetic fields during in
stallation and operation!

Persons fitted with heart pacemakers, metallic implants and hearing aids
etc. must not be allowed access to the following areas:

●

Areas where drive systems are installed, repaired and operated.

●

Areas where motors are installed, repaired and operated. Motors with
permanent magnets pose a particular hazard.

If it is necessary to access such areas, suitability to do so must be deter
mined beforehand by a doctor.

2.4

Safety instructions for maintenance

WARNING!

●

If this device is damaged, the device must be taken out of commission
and repaired or replaced.

«
...
15
16
17
18
19
...
»

Содержание D3DP 3 Series



















































































Отзывы:

Нет отзывов