KEB Combivert R6 Скачать руководство пользователя страница 26

Страница: 26 / 60

Installation

4.1

EMC-compatible control cabinet installation

Main fuse

150 mm

30 mm

150 mm

10b

10a

10c

11a

150 mm

Main contactor

EMC side-mounted filter

(>=size 25 R-S or R6-N)

EMC sub-mounted filter

(<=size 19 R6-S)

If necessary, external voltage limi-

tation / synchronisation

Commutation reactor / harmonic

filter

COMBIVERT R6

if necessary, external DC fuses

Frequency inverter

DC lines with ferrite

DC-

Motor line with ferrite

10a Equipotential bonding with the

housing earth

10b Protective Earth (PE) on the

mounting plate power circuit

10c

Protective Earth (PE) on the

mounting plate control circuit

Mains connection power circuit

11 A Mains connection control circuit
12

Control lines
Large area contact at the mount-

ing plate

Figure 10:

EMC-compatible control cabinet installation

4.2

Installation instructions

Warning

General installation instructions

• Stationary install and earth COMBIVERT.

• The device must not be permeated by mist or water.

•

Allow for sufficient heat dissipation if installed in a dust-proof housing.

• Install the COMBIVERT in an appropriate housing in accordance with the local regulations

when operating it in explosion-endangered spaces.

• Protect COMBIVERT against conductive and aggressive gases and liquids.

• The lines of the R6-N commutation reactor must be limiting to 1m.

• The frequency inverter must be placed in the immediate environment of the R6-N.

Содержание Combivert R6





























































Результаты поиска

Содержание Combivert R6

Отзывы:

Бренды по названию

Популярные бренды

KEB Combivert R6, Инструкция по эксплуатации

Результаты поиска

Содержание Combivert R6

Отзывы:

Бренды по названию

Популярные бренды