background image

4

PrefAce 

Laws and guidelines

KEB Automation KG confirms with the EC declaration of conformity and the CE mark on 

the device nameplate that it complies with the essential safety requirements.
The EC declaration of conformity can be downloaded on demand via our website. Fur-

ther information is provided in chapter "Certification".

Warranty and liability

The warranty and liability on design, material or workmanship for the acquired device is 

given in the general sales conditions.

Here you will find our general sales conditions.

www.keb.de/terms-and-conditions

Further agreements or specifications require a written confirmation.

Support   

Through multiple applications not every imaginable case has been taken into ac-

count. If you require further information or if problems occur which are not treated de-

tailed in the documentation, you can request the necessary information via the local 

KEB Automation KG agency.

The use of our units in the target products is outside of our control and therefore 

lies exclusively in the area of responsibility of the customer.

The information contained in the technical documentation, as well as any user-specific 

advice in spoken and written and through tests, are made to best of our knowledge and 

information about the intended use. However, they are regarded as being only informal 

and changes are expressly reserved, in particular due to technical changes. This also 

applies to any violation of industrial property rights of a third-party. Selection of our units 

in view of their suitability for the intended use must be done generally by the user. 

Tests can only be done within the intended end use of the product (application) by 

the customer. They must be repeated, even if only parts of hardware, software or 

the unit adjustment are modified. 

copyright

The customer may use the instructions for use as well as further documents or parts 

from it for internal purposes. Copyrights are with KEB Automation KG and remain valid 

in its entirety.
This KEB product or parts thereof may contain third-party software, including free and/

or open source software. If applicable, the license terms of this software are contained 

in the instructions for use. The instructions for use are already available to you, can be 

downloaded free of charge from the KEB website or can be requested from the respec-

tive KEB contact person.
Other wordmarks or/and logos are trademarks (™) or registered trademarks (®) of their 

respective owners.

Содержание COMBIVERT G6 series





















































Отзывы: