KEB COMBIVERT G6 series страница 15 Скачать руководство пользователя | Manualshive

Страница: 15 / 52

background image

15

bASIc SAfeTy INSTrUcTIONS

ESD

Drive converters contain electrostatic sensitive components.

►

Avoid contact.

►

Wear ESD-protective clothing.

Do not store drive converters
•  in the environment of aggressive and/or conductive liquids or gases.
•  with direct sunlight.
•  outside the specified environmental conditions.

1.3 Installation

DANGer

Do not operate in an explosive environment!

EX

►

The COMBIVERT is not intended for the use in potentially explosive

environment.

cAUTION

Maximum design edges and high weight!

contusions and bruises!

►

Never stand under suspended loads.

►

Wear safety shoes.

►

Secure drive converter accordingly when using lifting gear.

•  To prevent damages to the device:
•  Make sure that no components are bent and/or isolation distances are changed.
•  The device must not be put into operation in case of mechanical defects. Non-

compliance with the applicable standards.

• Do not allow moisture or mist to penetrate the unit.
•

Avoid dust permeating the device. Allow for sufficient heat dissipation if installed in

a dust-proof housing.

• Note installation position and minimum distances to surrounding elements. Do not

cover the ventilation openings.

•

Mount the drive inverter according to the specified degree of protection.

• Make sure that no small parts fall into the COMBIVERT during assembly and wiring

(drilling chips, screws etc.). This also applies to mechanical components, which can

lose small parts during operation.

•

Check the reliable fit of the device connections in order to avoid contact resistances

and sparking.

• Do not walk-on drive converter.
• The safety instructions are to be kept!

«
...
13
14
15
16
17
...
»

Содержание COMBIVERT G6 series





















































Отзывы:

Нет отзывов

Похожие инструкции для COMBIVERT G6 series

FRENIC-Eco Series

Бренд: Fuji Electric Страницы: 112

C1400-CO-VS-0S-I03

Бренд: NTI AG Страницы: 20

Penta Power KBRG-255

Бренд: KB Electronics Страницы: 20

Бренд: National Instruments Страницы: 35

Бренд: Masterflex Страницы: 20

Бренд: Samsung Страницы: 2

Бренд: Robotis Страницы: 21

Бренд: Iomega Страницы: 17

Бренд: LS Страницы: 15

Бренд: LS ELECTRIC Страницы: 84

Redi-Flo Series

Бренд: Grundfos Страницы: 16

Бренд: KBB Страницы: 43

VLT HVAC Basic Drive FC 10

Бренд: Danfoss Страницы: 33

Бренд: ABB Страницы: 20

G-SOLWHI10/100E

Бренд: Elmo Страницы: 64

Classic Q3 Series

Бренд: Unitek Страницы: 32

StorageWorks 30ux

Бренд: HP Страницы: 13

COMBIVERT G6 series

Бренд: KEB Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды