KEB COMBIVERT F5-A, Руководство по применению, Страница: 99 / 552

Analog in- and outputs
© KEB, 2012-10 COMBIVERT F5-A, -E, -H Page 7.2 - 3
7
7.2 Analog in- and outputs
7.2.1 Brief description analog inputs
By selecting an input interface (An.00/ 10) input AN1 or AN2 can be adjusted to the applied input signal. By
An.20 the third analog input can be switched additionally to AN1. Subsequently the analog inputs are smoothed
in an electronic filter (
An.01/ 11/ 21) by averaging. A save mode can be adjusted with An.02/12/22 and activated
with a programmable input (
An.03/13/23). To avoid voltage fluctuations and ripple voltages around the zero
point the analog signal can be faded out around the zero point up to ±10 % (An.04/14/24). In the characteristic
amplifier the input signals can be influenced in X and Y direction as well as in the rise (
An.05...07/ 15...17/
25...27). At the
output of the characteristic amplifier the signal can be limited to minimum and maximum value
(An.08, 09/18, 19/28, 29). At the
output of the block it can be defined with
An.30 which analog signal serves
as reference value and which one serves as auxiliary value. The ru-Parameters are used for the display of the
analog signal pre and post amplifier. The internal values are limited to ±400%.
Picture 7.2.1 Principle of the analog inputs
+AN1 (X2A.1)
-AN1 (X2A.2)
+AN2 (X2A.3)
-AN2 (X2A.4)
+AN3 (opt.)
-AN3 (opt.)
400%
-400%
400%
-400%
An.18
An.19
An.1
An.11
An.4
An.14 ru.29
An.10
An.5
An.6
An.7
An.15
An.16
An.17
An.8
An.9
ru.30
An.30
ru.27 ru.28
0...±100%
An.0
0...±100%
±10V
0...±20mA
4...20mA
±10V
0...±20mA
4...20mA
An.28
An.29
An.21
An.24 ru.31
An.25
An.26
An.27
ru.32
An.20
An.12
An.13
An.2
An.3
An.22
An.23
Analog inputs
REF
AUX
An.00
An.01
An.02
An.03
An.04
An.05
An.06
An.07
An.08
An.09
An.10
An.11
An.12
An.13
An.14
An.15
An.16
An.17
An.18 AN1 interface selection
AN1 interference suppression filter
AN1 save mode
AN1 save mode input selection
AN1 Nullzero point hysteresis
AN1 amplification
AN1 offset X
AN1 offset Y
AN1 lower limit
AN1 upper limit
AN2 interface selection
AN2 interference suppression filter
AN2 save mode
AN2 input selection
AN2 zero point hysteresis
AN2 amplification
AN2 offset X
AN2 offset Y
AN2 lower limit
An.19
An.20
An.21
An.22
An.23
An.24
An.25
An.26
An.27
An.28
An.29
An.30
ru.27
ru.28
ru.29
ru.30
ru.31
ru.32 AN2 upper limit
AN3 interface selection
AN3 interference suppression filter
AN3 save mode
AN3 input selection
AN3 zero point hysteresis
AN3 amplification
AN3 offset X
AN3 offset Y
AN3 lower limit
AN3 upper limit
Selection Set Point-/Auxiliary Input AUX-
Function
AN1
pre amplifier display
AN1
post amplifier display
AN2
pre amplifier display
AN2
post amplifier display
AN3
pre amplifier display
AN3
post amplifier display