KEB COMBISTOP 38, Инструкция по эксплуатации

Страница: 19 / 58

19
DEvIcE DATA cOMbISTOP 38
3.2 Device data cOMbISTOP 38
3.2.1 Overview
Device size 02 03 04 05 06 07 08 09 10 11
Rated torque after
running-in at 20 °C
N version
1)
M
2N
/ Nm 5 10 20 36 70 100 150 250 500 1000
Rated torque after
running-in at 20 °C
H version
1)
M
2N
/ Nm 7.5 15 30 50 90 150 225 375 750 1500
Rated power N version
P
20
/ W 25 30 30 48 62 65 75 80 130 180
Rated power H version
P
20
/ W 25 30 30 48 75 90 90 115 180 280
Rated voltage
2)
U
N_dc
/ V 24 / 105 / 180 / 205
3)
Cyclic duration factor
ED
/ % 100
Speed for service
braking
n / rpm 3000 1500
Max. speed for
emergency braking
n
_max
/ rpm 6000 5000 4500 3500 3000 2000
Mass moment of inertia
J
/ 10
-3
kgm² 0.025 0.075 0.227 0.553 0.771 1.84 6.17 17.22 45.28 153.6
Nominal air gap
X
/ mm 0.2 0.3 0.4 0.5 0.6
Switching cycles for
half-wave rectifier
4)
SC1
/ rpm 60 25 5 2 1
Switching cycles for
bridge rectifier
4) SC2
/ rpm 120 75 75 50 10 5 3 2
Switching cycles with
power box DC
SC3 / rpm 55 40 40 25 5 2 1
─
Separation time
5)
t
2
/ ms 40 55 90 110 240 220 320 350 400 750
Separation time with
power box
5)
t
2
/ ms 20 35 50 60 120 120 150 170 180 ─
Response delay AC
6)
t
11_ac
/ ms 70 100 180 220 260 400 700 900 1400 3100
Response delay DC
6)
t
11_dc
/ ms 10 15 25 25 25 40 50 60 100 450
Engagig time AC
7)
t
1_ac
/ ms 100 150 200 240 330 650 900 1200 2000 3500
Engaging time DC
7)
t
1_dc
/ ms 20 30 50 55 90 120 180 220 300 1000
Feather key
according to
DIN 6885-1
Keyway
ISO class
B (optional F and H)
Table 5: Device data COMBISTOP Type 38
1)
The torques are based on a quasi-static measurement with a differential speed of 25
rpm
.
2)
Special voltage upon request.
3)
105 V / 180 V / 205 V fall under the Low-Voltage Directive => „11.1 EU declaration of conformity“ .
4)
Maximum permissible switching cycles for DC-switching, continuous operation (100 % ED) and max.
operating temperature of 80 °C.
5)
Separation time from switching on the current to the beginning of the torque drop. The values are to be
regarded as guidelines.
6)
Time from switching off the current until increase in torque. The values are to be regarded as guidelines.
7)
Time from switching off the current until reaching 0.9 x rated torque M
2N
. The values are to be regarded as
guidelines.