KAYO MOTOR TT 125 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 74

background image

Storage of motorcycles

The preparation of the motorcycle before long unused

When you plan to store your vehicle and not use it for a long
time, follow these steps:
1. Plug the exhaust port of the muffler cylinder;
2. Take out the battery.
3. Clean the motorcycle thoroughly;
4. Wait for the motorcycle to dry naturally;
5. Empty the tank (if not used for a long time, the gasoline will
deteriorate);
6. Lubrication chain;
7. Apply oil to all unpainted metal surfaces to prevent rust;
8. When storing the motorcycle, keep the motorcycle wheel
suspended, if the condition cannot be reached, the cardboard
pad can be used under the motorcycle tire;
9. Cover your motorcycle to prevent dirt and dirt from sticking.
10. Move the motorcycle into a dry room.

Note:

When applying anti-rust oil, please do not splash the oil

on the brake and rubber parts, otherwise it may make the rubber
aging.

Prepare a motorcycle before it is put into use after long unused

«
...
67
68
69
70
71
...
»

Содержание TT 125











































































Отзывы:

Нет отзывов

Похожие инструкции для TT 125

SEMIFARINGS ANARCHY

Бренд: CUSTOMACCES Страницы: 2

Бренд: Suzuki Страницы: 447

Splendor Pro CLASSIC

Бренд: HERO Страницы: 56

GRIZZLY 90 2020

Бренд: Yamaha Страницы: 132

Бренд: Yamaha Страницы: 132

Бренд: Yamaha Страницы: 166

Бренд: Yamaha Страницы: 452

Бренд: Yamaha Страницы: 132

Бренд: Yamaha Страницы: 112

Бренд: hepco & becker Страницы: 3

Бренд: hepco & becker Страницы: 2

Бренд: DYNATEK Страницы: 4

1003007FONTANASPRINT

Бренд: DYNATEK Страницы: 7

Бренд: Yamaha Страницы: 400

ZIEGER 10005243

Бренд: IBEX Страницы: 4

Бренд: Maat Страницы: 12

Бренд: Rally-Raid Страницы: 2

Бренд: Shad Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды