38
ED
IT
M
en
u
Overview of the EDIT Menu
(INT mode)
The EDIT menu contains various parameters that can be used to adjust the MP7SE’s MAIN and SUB zones in INT mode.
The parameters are grouped by category, allowing close control over the instrument with just a few button presses.
* The EDIT menu can also be used to adjust the parameters of zones in EXT mode. For more information, please refer to page 54.
This collection of parameters, together with other adjustable settings, can be stored as a SETUP memory (page
65). The MP7SE provides 256 user programmable SETUP memories.
About Common parameters ( icon)
Unless stated, parameter settings for the MAIN, SUB1, SUB2, and SUB3 zones are independent for each zone. However, parameters
marked with a icon are common for all four zones. For example, changing the Reverb Type parameter for the MAIN zone will
automatically change the Reverb Type parameter for the SUB1, SUB2, and SUB3 zones.
INT mode zone parameters
No. Category
Parameters
1
REVERB
Type, Pre Delay, Time, Depth
2
EFX
Category, Type, Parameters
(prm1~prm10, depending on EFX type)
AMP
Amp Type, Drive, Level, Amp EQ Lo, Amp EQ Mid, Amp EQ Hi, Mid Freq., Mic Type, Mic Position, Ambience
3
Sound
Master Volume, Panpot, Filter Cut-off, Filter Resonance, DCA Attack Time, DCA Decay Time, DCA Sustain Level,
DCA Release Time, DCF Attack Time, DCF Attack Level, DCF Decay Time, DCF Sustain Level, DCF Release Time,
DCF Touch Depth, DCA Touch Depth, Vibrate Depth, Vibrate Rate, Vibrate Delay, Octave Layer Switch,
Octave Layer Level, Octave Layer Range, Octave Layer Detune, Portamento, Porta. Time, Porta. Mode
tonewheel
: Drawbar Position, Percussion, Perc. Level, Perc. Decay, Perc. Harmonic,
Ext. Control
4
Tuning
Fine Tune, Stretch Tuning, Temperament, Key of Temperament
5
Key Setup
Touch Curve, Dynamics, Trigger Mode, Minimum Touch, Octave Shift, Zone Transpose, Key Scaling Damping,
Key Scaling Key, Key Range Zone Lo, Key Range Zone Hi, Velocity Switch, Velocity Switch Value, Solo,
Solo Mode, Key Volume
6
Controllers
Damper Pedal, Damper Pedal Assign, Damper Pedal Mode, Pitch Bend, P. Bend Range, Soft Pedal Depth,
Modulation Wheel, Modulation Wheel Assign, Modulation Depth Range, SW1 Button, SW1 Button Assign,
SW2 Button, SW2 Button Assign, Footswitch Pedal, Footswitch Pedal Assign, Expression Pedal,
Expression Pedal Assign, Right Pedal, Right Pedal Assign, Center Pedal, Center Pedal Assign, Left Pedal,
Left Pedal Assign
7
Knob Assign
Knob A Assign, Knob B Assign, Knob C Assign, Knob D Assign,
Knob2 A Assign, Knob2 B Assign, Knob2 C Assign, Knob2 D Assign
8
Virtual
Technician
piano
: Voicing, String Resonance, Undamped Resonance, Damper Resonance, Key-off Effect, Damper Noise,
Hammer Delay, Fall-back Noise, Topboard, Stereo Width
e
.
piano
/
harpsi
/
bass
: Key-off Noise, Key-off Delay
drawbar
: Key Click Level, Wheel Noise Level
Entering the EDIT Menu
When the zone is in INT mode:
Press the EDIT button.
The LED indicator for the EDIT button will turn ON, and the Edit
Menu for the selected zone will be shown in the LCD display.
MAIN
zone
selected
LED indicator ON:
EDIT mode is turned ON
* To change the selected zone, press the F1~F4 function buttons.