KaVo ProXam iOS Скачать руководство пользователя страница 13

Страница: 13 / 130

4 Safety precautions

The user must read and comply with all safety, warning, and instructional

labels on the scanner.
Ensure your scanner is properly maintained through periodic maintenance. If

you suspect equipment malfunction or failure, discontinue using the scanner

and contact technical support immediately. Do not attempt to make any

repairs on the scanner.
Warning denotes something that can cause personal injury to the patient or

the user.
Caution denotes something that can cause damage to the equipment.

WARNING

Failure to adhere to all safety warnings may result in personal injury,

equipment damage, or data loss.

WARNING

Do not use the scanner for any purpose other than its intended and labelled

use.

WARNING

This is a Class A product. In a domestic environment the scanner may cause

radio interference in which case the user may be required to take adequate

measures.

WARNING

When connecting the components, use only the cables supplied with the

scanner. Failure to do so may result in increased electromagnetic emissions

or reduced immunity to external electromagnetic emissions.

WARNING

Do not make any unauthorised repairs or modifications to the system

software or hardware. This includes installing unauthorised software on

the host computer system or altering or bypassing any safety switches

or mechanisms. Changes or modifications not expressly approved by the

manufacturer could void the user’s authority to operate the equipment.

WARNING

Do not install or operate the scanner in an environment where an explosion

hazard exists, for example in a high oxygen area.

WARNING

Do not attach any equipment or devices to the scanner unless their use has

been specifically authorised by the manufacturer.

4 Safety precautions

Instructions for use

KaVo ProXam iOS 7

Содержание ProXam iOS



































































































































Результаты поиска

Содержание ProXam iOS

Отзывы:

Бренды по названию

Популярные бренды

KaVo ProXam iOS, Инструкция по эксплуатации

Результаты поиска

Содержание ProXam iOS

Отзывы:

Бренды по названию

Популярные бренды