KaVo KEY Laser 3+ 1343 Скачать руководство пользователя

Страница: 75 / 80

Assembly instructions

9.1

Floor composition

The quality of the floor (screed) must comply with the load bearing capacity for

buildings

DIN 1055 page 3 , and the pressure resistance must correspond to DIN

18560 T1 .

The KEY Laser 3+ / III upgraded is delivered from the factory with soft castors.

Note
The castors may not be used on soft floors (rugs, etc.).

The screed, floor covering, adhesive and floor sealant must be appropriate for

castors.

KaVo assumes no liability for any damage that may occur if the castors are im‐

properly used on different floor coverings.

9.2

Media

9.2.1

Spray water

The KEY Laser 3+ / III upgraded has an internal spray water supply.

The spray water storage bottle may be filled only with distilled or demineralised water

(neutral pH).

9.2.2

Spray air

A compressor is integrated in the KEY Laser 3+ / III upgraded to generate a system

air supply.

9.3

Electrical connection

CAUTION

Damage to the unit from wrong fuses or supply cables.

Damage to the unit.

▶ Provide separate fuses for the KEY Laser 3+ / III upgraded.

▶ Use a separate supply cable for the KEY Laser 3+ / III.

9.3.1

Customer

▪ The connection must correspond to the provisions of VDE 0100 for Schuko

sockets.

▪ Connection for USA 125V/30 AMP corresponding to NEMA 5-30R

▪ 230 V fuses with B16 or C16 m.c.b.

▪ 100-127 V fuses with 25 A

▪ 100-127 V fuses with 20 A, for Japan only

Instructions for use KEY Laser 3+ 1343 KEY Laser III 1243 upgraded
9 Assembly instructions | 9.1 Floor composition

73/76

Содержание KEY Laser 3+ 1343

















































































Результаты поиска

Содержание KEY Laser 3+ 1343

Отзывы:

Похожие инструкции для KEY Laser 3+ 1343

Бренды по названию

Популярные бренды

KaVo KEY Laser 3+ 1343, Инструкция по эксплуатации

Результаты поиска

Содержание KEY Laser 3+ 1343

Отзывы:

Похожие инструкции для KEY Laser 3+ 1343

Бренды по названию

Популярные бренды