KaVo EXTRAmatic 9040 Скачать руководство пользователя страница 7

Страница: 7 / 56

Instructions for use EXTRAmatic 9040

1 User notes | 1.4 Transportation and storage

4. Report the damage to the shipping company.

5. Report the damage to KaVo.

6. Consult with KaVo first, before returning a damaged product.

7. Send the signed delivery receipt to KaVo.

If the product is damaged but there was no discernable damage to the packaging

upon delivery, proceed as follows:

1. Report the damage to the shipping company immediately and no later than 7 days

after delivery.

2. Report the damage to KaVo.

3. Leave the product and packaging in the condition in which you received it.

4. Do not use a damaged product.

Note

If the recipient fails to comply with any of the above-mentioned obligations, the

damage will be considered to have arisen after delivery

(in accordance with the General German Freight Forwarders´ Terms and Conditions, Art. 28)

Outside Germany

Note

KaVo shall not be held liable for damage arising from transportation.
The shipment must be checked on arrival.

If the packaging is visibly damaged on delivery, please proceed as follows:

1. The recipient of the package must record the loss or damage on the delivery re‐

ceipt. The recipient and the representative of the shipping company must sign this

delivery receipt.

Without this evidence, the recipient will not be able to assert a claim for damages

against the shipping company.

2. Leave the product and packaging in the condition in which you received it.

3. Do not use the product.

If the product is damaged but there was no discernable damage to the packaging

upon delivery, proceed as follows:

1. Report any damage to the shipping company either immediately or no later than 7

days after delivery.

2. Leave the product and packaging in the condition in which you received it.

3. Do not use a damaged product.

Note

If the recipient fails to comply with any of the above-mentioned obligations, the

damage will be considered to have arisen after delivery

(in accordance with CMR law, Chapter 5, Art. 30).

1.4.3 Transportation and storage

Note

When transporting used equipment (already exposed to dust), seal tight the intake

openings on the rear of the device (e.g. with duct tape).

7 / 56

Содержание EXTRAmatic 9040

























































Результаты поиска

Содержание EXTRAmatic 9040

Отзывы:

Бренды по названию

Популярные бренды

KaVo EXTRAmatic 9040, Инструкция по эксплуатации

Результаты поиска

Содержание EXTRAmatic 9040

Отзывы:

Бренды по названию

Популярные бренды