background image

WLAN VDSL Gateway 

       

User Manual 

42 

 

Appendix:    Frequent Asked Questions   

Q:    None of the LEDs are on when you power on the ADSL router? 
A:    Please make sure what you use is the power adaptor attached with the ADSL 

router package and checks the connection between the AC power and ADSL 
router.   

 
Q:    DSL LED does not turn on after connect telephone line? 
A:    Please make sure what you use is the standard telephone line (as attached with 

the package), make sure the line is connected correctly and check whether there 
is poor contact at each interface. Wait for 30 seconds to allow the ADSL router 
establishes connection with you ADSL operator.   

 
Q:    DSL LED is in the circulation of slow-flashing and fast-flashing after connecting 
telephone line? 
A:    This situation means the ADSL router is in the status of failing to establish 

connection with Central Office. Please check carefully and confirm whether the 
ADSL router has been installed correctly. 

 
Q:    LAN LED does not turn on after connect Ethernet cable? 
A:    Please make sure Ethernet cable is connected hub/PC and ADSL router correctly. 

Then please make sure the PC/hub have been power on. 

Please make sure that you use parallel network cable to connect UpLink port of 
hub, or use parallel network cable to connect PC. If connect normal port of hub 
(not UpLink port), you must use cross-cable. Please make sure that your network 
cables meet the networking requirements above. 

 
Q:    PC cannot access the Router? 
A:    Please make sure that all devices communicating with the device must use the 

same channel (and use the same SSID). Otherwise your PC will not find the 
wireless Router. 

 
Q:    PC cannot access the Internet?   
A:    First check whether PC can ping the interface Ethernet IP address of this product 

successfully (default value is 192.168.1.1) by using ping application. If ping 
application fails, please check the connection of Ethernet cable and check 
whether the states of LEDs are in gear. 

If the PC uses private IP address that is set manually (non-registered legal IP 
address), please check: 

1.  Whether IP address of the PC gateway is legal IP address. Otherwise please 

use the right gateway, or set the PC to Obtain an IP address automatically. 

2.  Please confirm the validity of DNS server appointed to the PC with ADSL 

operator. Otherwise please use the right DNS, or set the PC to Obtain an IP 
address automatically.   

3.  Please make sure you have set the NAT rules and convert private IP address 

to legal IP address. IP address range of the PC that you specify should meet 
the setting range in NAT rules.   

4.  Central Office equipment may have problem. 
5.  The country or the wireless network type you selected is wrong.   

 
 

Содержание KW5225














































Отзывы: