Kärcher VC 6 Cordless ourFamily, Руководство пользователя

Страница: 13 / 164

English 13
ATTENTION
Material damage due to incorrect battery storage
Incorrect storage during charging can result in the bat-
tery e.g. falling down or damaging heat-sensitive surfac-
es.
Make sure charging of the separate battery takes place
on a flat, smooth and heat-insensitive surface.
Furthermore, the battery should not be covered with ob-
jects (e.g. fabrics or papers) while it is being charged.
3. Plug the charger into a socket.
Insert the connecting plug into the charging socket
of the wall bracket / battery.
Depending on the battery status, the 3 LED indicator
lights flash or light up green during the charging pro-
cess.
Illustration G
4. When the device is fully charged, all 3 LED indicator
lights light up continuously green for 2 minutes and
then go out.
Remove the charger from the socket/charging cable
from the battery charging socket and socket.
Illustration H
5. Remove the device from the wall bracket or insert
the battery into the device, see chapter Inserting the
battery
The device is ready for use.
Removing the battery
몇
WARNING
Uncontrolled startup
Risk of injury
Remove the battery from the device before service and
care work or if the device is not going to be used for a
long period of time.
1. Press the unlocking button.
2. Remove the battery from the device.
Illustration I
Operation
LED display
The LEDs on the head of the device and on the battery
indicate information about the battery status, boost
mode and error messages.
The charging state of the battery is indicated by the
3 green LEDs on the device as well as by the 3 green
LEDs on the battery.
See figure A on the graphics page and chapter
Device
description
The charging progress of the battery is indicated by the
3 green LEDs on the device as well as by the 3 green
LEDs on the battery. The LEDs only light up when the
battery is correctly installed.
Changing accessories
To change accessories, see chapter Installing accesso-
ries
Vacuuming
1. Install the required accessories, see chapter Install-
ing accessories .
2. Switch on the device, depending on cleaning re-
quirements:
 Press the On/Off switch and keep it pressed dur-
ing operation.
or
 Turn the locking lever to switch the device directly
to continuous operation.
Illustration J
3. If necessary, press the Boost button to increase the
dust intake.
Illustration K
Battery charging state
LED Duration of
lighting Meaning
1st LED flashes
green 1 s on / 1 s off Battery charged below
7.5 %
1st LED lights up
green continuously Battery charged below
40 %
1st and
2nd LEDs light
up green continuously Battery charged below
70 %
3 LEDs light up
green continuously Battery charged
above 70 %
3 LEDs flash
green 125 ms on /
125 ms off Battery fault, after 30 s
the signal goes out
While charging
LED Duration of
lighting Meaning
1st LED flashes
green 0.2 s from off
to on /
0.6 s on /
0.2 s from on
to off /
1 s off Battery charging, battery
charged below 40 %
1st LED lights
up green
2nd LED flashes
green continuously
0.2 s from off
to on /
0.6 s on /
0.2 s from on
to off /
1 s off Battery charging, bat-
tery charged below
70 %
1st and
2nd LEDs light
up green
3rd LED flashes
green continuously
0.2 s from off
to on /
0.6 s on /
0.2 s from on
to off /
1 s off Battery charging, battery
charged below 99 %
3 LEDs light up
green 2 min contin-
uous lighting,
then off Battery fully charged
Error message
LED Duration of
lighting Meaning
Suction duct
flashes red 125 ms on / 125
ms off Suction channel
clogged
Floor nozzle
LED flashes
red 125 ms on / 125
ms off Floor nozzle blocked
See also chapter Troubleshooting guide
Boost mode
LED Duration of
lighting Meaning
LED half ring
lights up green continuously Boost mode on