Kärcher NT 65/2 Ap Tc, Руководство пользователя

Страница: 11 / 104

English 11
Switching on the device
1. Connect the mains plug.
2. Switch on the device at the main switch.
Semi-automatic filter dedusting
Note
Actuating the semi-automatic filter dedusting every 5-10
minutes extends the working time of the flat fold filter.
Note
The semi-automatic filter dedusting can only be
switched on when the device is switched on.
1. Press the semi-automatic filter dedusting button 5x.
The flat fold filter is then cleaned by a blast of air
(pulsing noise).
Switching off the device
1. Press the semi-automatic filter dedusting button 5x.
2. Switch off the device at the main switch.
3. Pull out the mains plug.
Each time after use
1. Empty the container.
2. Vacuum off the inside and outside of the device and
clean with a moist cloth.
Folding the push handle in/out
1. Release the push handle fastening screws and ad-
just the push handle.
Storing the device
1. Store the suction hose and mains cable as shown in
the illustration.
Illustration I
2. Store the device in a dry room and secure it against
unauthorised use.
Transport
몇 CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
1. Remove the suction hose with floor nozzle from the
support. Carry the device by the carrying handle and
suction pipe.
2. Load the device by the chassis handle and push
handle.
3. Pull the device behind you via the push handle for
transporting over longer distances.
4. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respective valid guidelines.
Storage
몇 CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
The device may only be operated indoors.
Care and service
 DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the mains plug.
Replacing the flat fold filter
1. Open the filter cover.
2. Remove the flat fold filter.
3. Fit the new flat fold filter. During insertion, ensure
that the flat fold filter is flush on all sides.
4. Close the filter cover until it audibly latches into
place.
Cleaning the electrodes
1. Unlock and remove the suction head.
2. Clean the electrodes and the gap between the elec-
trodes with a brush.
3. Fit and lock the suction head.
Troubleshooting guide
 DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the mains plug.
Suction turbine does not start up
1. Check the socket and the power supply fuse.
2. Check the mains cable, mains plug and electrodes
on the device.
3. Switch on the device.
Suction turbine switches off
1. Empty the container.
Suction turbine does not switch on again after emp-
tying the container
1. Switch off the device and wait for 5 seconds. Switch
on the device.
2. Clean the electrodes and the gap between the elec-
trodes with a brush.
Suction power decreases
1. Remove any blockages from the suction nozzle,
suction pipe, suction hose or flat fold filter.
2. Change the filled paper filter bag.
3. Press the semi-automatic filter dedusting button 5x
with the device switched on.
4. Correctly engage the filter cover.
5. Replace the flat fold filter.
6. Check the drain hose for leaks.
Escaping dust when vacuuming
1. Check that the flat fold filter is correctly fitted and
correct if necessary.
2. Replace the flat fold filter.
The automatic switch-off mechanism (wet vacuum
cleaning) does not trigger
1. Clean the electrodes and the gap between the elec-
trodes with a brush.
2. Continuously monitor the filling level when vacuum-
ing non-conductive liquids.
Semi-automatic filter dedusting not working
1. Suction hose not connected.
Semi-automatic filter dedusting does not switch off
1. Contact Customer Service.
Semi-automatic filter dedusting cannot be switched
on
1. Contact Customer Service.
Customer Service department
If the malfunction cannot be corrected, the device must
be checked by the Customer Service department.