Kärcher HD 6/15 M, Руководство пользователя

Страница: 18 / 208

18 English
Have electrical components checked and repaired by
the authorised Customer Service.
In case of any malfunctions not mentioned in this chap-
ter, contact the authorised Customer Service when in
doubt or when you have been explicitly advised to do
so.
Device does not start
 Check the power cable for damage.
 Check the mains voltage.
 If the device overheats:
a Set the power switch to "0".
b Allow the device to cool for at least 15 minutes.
c Set the power switch to "1".
 Contact Customer Service in the case of electrical
faults.
Device does not reach required pressure
 Check the size of the nozzle and compare with the
required size specified in the "Technical data" sec-
tion.
 Vent the device, see section "Venting the device".
 Clean the sieve in the water connection.
 Check the water supply volume and compare with
the required volume specified in the "Technical data"
section.
 Clean the nozzle.
 Contact Customer Service if necessary.
Pump leaking
Up to 3 drops of water per minute are permissible.
 In case of more serious leaks, have the device
checked by Customer Service.
Pump knocking
 Check the water supply line for leaks.
 Vent the device, see section "Venting the device".
 Contact Customer Service if necessary.
Detergent dosing volume too low
 Refill the foam nozzle cup.
 Plug a larger blender onto the suction hose.
 Check the suction hose and foam nozzle for deter-
gent deposits. Remove deposits using lukewarm
water.
Accessories and spare parts
Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and
safely.
Information on accessories and spare parts can be
found at
www.kaercher.com .
Warranty
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Technical data
HD 6/15
M HD 6/15
MX HD 6/15
M PU HD 7/17
M HD 7/17
MX HD 7/17
M PU HD 7/
14-4 M
Electrical connection
Mains voltage V 230 230 230 400 400 400 230
Phase ~ 1 1 1 3 3 3 1
Power frequency Hz 50 50 50 50 50 50 50
Connection output kW 3.1 3.1 3.1 4.2 4.2 4.2 3.4
Protection class IPX5 IPX5 IPX5 IPX5 IPX5 IPX5 IPX5
Power protection (slow-blowing) A 16 16 16 16 16 16 16
Extension cable, 30m mm
2
2.5 2.5 2.5 2.5 2.5 2.5 2.5
Water connection
Feed pressure (max.) MPa 1 1 1 1 1 1
Input temperature (max.) °C 60 60 60 60 60 60 60
Input amount (min.) l/min 12 12 12 12 12 12 12
Suction height (max.) m 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Performance data of device
Nozzle size of standard nozzle -- 033 033 033 038 038 038 043
Operating pressure MPa 15 15 15 17 17 17 14
Operating pressure (max.) MPa 22.5 22.5 22.5 25.5 25.5 25.5 21
Water flow rate l/min 9.3 9.3 9.3 11.5 11.6 11.6 11.5
High-pressure gun recoil force N 21.3 21.3 21.3 21.3 21.3 21.3 21.3
Dimensions and weights
Typical operating weight kg 30 33 25 32 35 27 39
Length mm 455 455 290 455 455 290 455
Width mm 400 400 300 400 400 300 400
Height of push handle, bottom, (top) mm 700
(970) 890
(970) 565 700
(970) 890
(970) 565 700
(970)