Kärcher CVS 65/1 Bp Скачать руководство пользователя страница 3

English

3

General

Before starting operation, the device must be in the operating po-
sition.
Do not start or operate the device, any of its functions or attach-
ments, from any place other than from the designated operator's 
position.
Before leaving the operator’s position:
1 bring the device to a complete stop;
2 if the device must be on an incline, block the wheels.
Maintain a safe distance from the edge of ramps, platforms, and 
other similar working surfaces.
Do not add to, or modify the device.
Do not block access to fire aisles, stairways or fire equipment.

Traveling

Yield the right of way to pedestrians and emergency vehicles 
such as ambulances and fire trucks.
Cross railroad tracks at an angle wherever possible. Do not park 
closer than 6 ft (1800 mm) to the nearest rail of a railroad track.
Keep a clear view of the path of travel and observe for other traf-
fic, personnel, and safe clearances.
Under all travel conditions, operate the device at a speed that will 
permit it to be brought to a stop in a safe manner.
Do not indulge in stunt driving or horseplay.
Slow down for wet and slippery floors. Before driving over a dock-
board or bridge plate, be sure that it is properly secured. Drive 
carefully and slowly across the dockboard or bridge plate, and 
never exceed its rated capacity.
When negotiating turns, reduce speed to a safe level consistent 
with the operating environment. Make the turns smoothly.

Operator care of the device

If the device is found to be in need of repair or in any way unsafe, 
or contributes to an unsafe condition, the matter shall be reported 
immediately to the user’s designated authority, and the device 
shall not be operated until it has been restored to safe operating 
condition.
If during operation the device becomes unsafe in any way, the 
matter shall be reported immediately to the user’s designated au-
thority, and the device shall not be operated until it has been re-
stored to safe operating condition.
Do not make repairs or adjustments unless specifically autho-
rized to do so.

MAINTENANCE AND REBUILD PRACTICES

Operation of the device may be hazardous if maintenance is ne-
glected or repairs, rebuilds, or adjustments are not performed in 
accordance with the manufacturer’s design criteria. Therefore, 
maintenance facilities (on or off premises), trained personnel, 
and detailed procedures shall be provided.
Maintenance and inspection of the device shall be performed in 
conformance with the following practices:
1 a scheduled planned maintenance, lubrication, and inspection 

system shall be followed; consult the manufacturer’s recom-
mendations.

2 Only trained and authorized persons shall be permitted to op-

erate a powered floor scrubber. Operators of powered floor 
scrubbers shall be qualified as to visual, auditory, physical, 
and mental ability to operate the equipment safely.

Avoid fire hazards and have fire protection equipment present in 
the work area. Do not use open pans of fuel or flammable clean-
ing fluids for cleaning parts.

FIRE SAFETY STANDARD

Any device not in safe operating condition shall be removed from 
service.
Repairs shall not be made in Class I, Class II, and Class III loca-
tions.

Fire Prevention.

The device shall be kept in a clean condition 

and reasonably free of lint, excess oil, and grease.
Noncombustible agents are preferred for cleaning the device. 
Flammable liquids [those having flash points at or above 100°F 
(37,8°C)] are not allowed. Precautions regarding toxicity, ventila-
tion, and fire hazard shall be appropriate for the agent or solvent 
used.

Nameplate Visibility. 

The device type designations as shown on 

the nameplate and the type markers shall not be covered over 
with paint so that their identification information is obscured.

General notes

Read these original instructions and the safety in-
structions chapter before using the device for the first 
time. Proceed accordingly.

Keep these for future reference or for future owners.

Check delivery

When handing over the vehicle, please report any defects and 
shipping damage to your dealer or sales outlet immediately.

Environmental protection

The packing materials can be recycled. Please dispose of 
packaging in accordance with the environmental regula-

tions.

Electrical and electronic appliances / devices contain valu-
able, recyclable materials and often components such as 
batteries, rechargeable batteries or oil, which - if handled or 

disposed of incorrectly - can pose a potential threat to human 
health and the environment. However, these components are re-
quired for the correct operation of the appliance / device. Appli-
ances / devices marked by this symbol are not allowed to be 
disposed of together with the household trash.

Notes on the content materials (REACH)

Current information on content materials can be found at: 

www.kaercher.de/REACH

Warranty

The warranty conditions issued by our relevant sales company 
apply in all countries. We shall remedy possible malfunctions on 
your appliance within the warranty period free of cost, provided 
that a material or manufacturing flaw is the cause. In a warranty 
case, please contact your dealer (with the purchase receipt) or 
the next authorized customer service site.
(See overleaf for the address)

Accessories and spare parts

Only use original accessories and original spare parts. They en-
sure that the appliance will run fault-free and safely.
Information on accessories and spare parts can be found at 

www.kaercher.com

.

Hazard levels

DANGER

Indication of an imminent threat of danger that will lead to se-
vere injuries or even death.

WARNING

Indication of a potentially dangerous situation that may lead to 
severe injuries or even death.

CAUTION

Indication of a potentially dangerous situation that may lead to 
minor injuries.

ATTENTION

Indication of a potentially dangerous situation that may lead to 
damage to property.

Содержание CVS 65/1 Bp

































Отзывы: