manualshive.com logo in svg

Kärcher BR 30/4 C, Руководство по обслуживанию

Поделиться
Скачать
Kärcher BR 30/4 C Скачать руководство пользователя страница 22

22 

English 5.906-434.0 Rev. 00 (12/10)

1 Vacuum bar

The vacuum bars can be replaced without the use of 
tools.

Î

Move the pedal for the vacuum bar lift to the pedal 
position "vacuum bar lowered" (see Chapter 
"Raising/lowering the vacuum bar“).

Î

Pull the vacuum bar out of the vacuum bar sup-
port.

Î

Insert the new vacuum bar from the bottom into 
the vacuum bar support from the bottom and press 
upward, until the vacuum bar is locked with an au-
dible "click".

Note
The standard suction bar is not suitable for vacuum-
ing oil-soiled floors. In this case, you must use oiltight 
suction lips.

Î

Remove the front vacuum bar (see chapter "Re-
placing the vacuum bar").

1 Fastening screws (8x), cleaning head housing

Î

Unscrew locking screws.

1 Fastening screws (2x), wheel mount

Î

Unscrew the cap and fastening screw of the wheel 
mount and remove the wheel.

1 Fastening screws (2x) per side, cleaning head 

housing

2 Mount, release park position
3 Intake, fastening screw, wheel mount

5.1.6 Replace the vacuum bar.

5.1.7 Removing the cleaning head housing

Содержание BR 30/4 C









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды