Kärcher BLV 18-200 Battery, Руководство пользователя

Страница: 17 / 212

English 17
c Pull out the motor casing locking pin as far as
possible.
d Remove the upper blower and suction pipe from
the motor casing.
5. If necessary, remove any blockage from the pipes.
6. If necessary, remove any blockage in the adapter.
7. If necessary, remove any blockage from the con-
necting piece.
8. Clean the openings of the motor casing.
Troubleshooting guide
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service. As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Warranty
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Technical data
Subject to technical modifications.
Vibration value
몇
WARNING
The specified vibration value was measured using a
standard test procedure and may be used to compare
devices.
The specified vibration value may be used in a provi-
sional assessment of the load.
Depending on the way the device is used, the vibration
emission can deviate from the specified overall value
during the current use of the device.
Fault Cause Rectification
The device does not start
up Battery pack is not inserted correctly.  Push the battery pack into the mounting
until it latches into place.
Battery pack is empty  Charge the battery pack.
Battery pack is defective.  Replace the battery pack.
Safety button did not trip during assem-
bly. 1. Unscrew the suction pipe fixing screw once
again.
2. Tighten the suction pipe fixing screw until a
clicking sound is heard.
The safety button has tripped.
The device stops during
operation The battery has overheated  Stop working and allow the battery to cool
down to normal battery temperature.
Motor has overheated  Stop working and allow the motor to cool
down.
BLV 18-
200
Device performance data
Nominal voltage V 18
Average air speed of cordless
blower km/h 152,9 +/-
10 %
Average air speed of cordless
blower (turbo mode) km/h 186,7 +/-
10 %
Maximum theoretical air speed of
cordless blower km/h 186,7 +/
- 10 %
Maximum theoretical air speed of
cordless blower (turbo mode) km/h 262,9 +/
- 10 %
Average air speed of cordless
suction device km/h 112,7 +/-
10 %
Average air speed of cordless
suction device (turbo mode) km/h 135,2 +/-
10 %
Maximum theoretical air speed of
cordless suction device km/h 138,4 +/
- 10 %
Maximum theoretical air speed of
cordless suction device (turbo
mode) km/h 162,6 +/
- 10 %
Mulch ratio 10:1
Collecting bag volume l 45
Dimensions and weights
Weight (without battery pack) kg 3,5
Length x width x height mm 1243 x
171 x
376
Determined values in acc. with EN 50636-2-100
Sound level L
pA
Cordless blower dB(A) 87,6
Sound level L
pA
Cordless blower/
vacuum
dB(A) 90,8
Uncertainty K
pA
dB(A) 3,0
Sound power level L
WA
+ K uncer-
tainty
WA
dB(A) 107
Total vibration value for cordless
blower m/s
2
3,0
Total vibration value for cordless
blower/vacuum m/s
2
3,5
Uncertainty K m/s
2
1,5
BLV 18-
200