background image

5

15

Socket for additional brush wash head 

PW 30/1 (Puzzi 10/2 Adv only)

16

Suction hose connection

17

Defoaming agent container (Puzzi 10/2 

Adv only)

18

Cover

19

Storage compartment for detergent tabs 

(Puzzi 10/2 Adv only)

20

Device carrying handle including suc-

tion pipe holder

21

Floor nozzle for carpet cleaning

22

Carpet adapter

23

Floor nozzle latch

24

Suction pipe

25

Nozzle mouthpiece

26

Union nut

27

Handle

28

Angle piece

29

Lever on the manifold

30

Spray hose

31

Suction hose

32

Spray / suction hose

33

Wastewater container, removable

34

Wastewater container carrying handle

35

Cover seal

36

Fluff filter

Start-up

1. Check the power cord, extension cable

and hoses for damage before each start-
up.

Installing accessories

1. Fit the suction pipe onto the floor nozzle

and hand-tighten the union nut on the
floor nozzle.

2. If necessary, slide the handle onto the

suction pipe and hand-tighten in the de-
sired position.

3. Fit the angle piece onto the suction pipe

and hand-tighten the union nut on the
angle piece.

4. Connect the suction hose to the suction

hose connection on the device. Insert
the spray hose coupling into the spray
hose connection on the device and latch 
into place.

5. Connect the suction hose to the angle

piece. Connect the spray hose coupling
to the angle piece and latch into place.

Mixing the cleaning solution

DANGER

Danger from detergents

Risk of injury and damage
Observe all instructions that are included
with the detergents used.

Note

Warm water (maximum 50 °C) increases
the cleaning effect. Check the temperature
resistance of the surface to be cleaned.

Note

Use detergents sparingly to conserve the
environment.

1. Mix fresh water and detergent in a clean

container (concentration as specified for 
the detergent). Dissolve the detergent in 
the water.

Filling the fresh water tank

1. Pour the cleaning solution into the fresh

water tank. The filling level must not ex-
ceed the "MAX" mark.

Defoaming agent

Note

Foam is generated in the wastewater con-
tainer when cleaning previously sham-
pooed carpets. Foaming can be prevented 
by adding defoaming agents.

1. Puzzi 10/1 only: Add defoaming agent

(special accessory) to the wastewater
container.

2. Puzzi 10/2 Adv only: Open the defoam-

ing agent container. Fill with defoaming
agent (special accessories).

Replacing the carpet adapter

1. Press the floor nozzle latch on one side.
2. Swing out and remove the carpet adapt-

er.

3. Insert a new carpet adapter and engage

the latch.

Operation

Working with accessories

Puzzi 10/2 Adv only:

Note

An additional power socket is provided for 
connecting additional electrical devices.

Содержание 14/1411













Отзывы: