background image

15

Operations

Storage

CAUTION: Always store your pressure washer in a 
location where the temperature will not fall below 
32°F (0°C). The pump in this machine is susceptible 
to permanent damage if frozen. FREEZE DAMAGE 
IS NOT COVERED BY WARRANTY.

Attention : Toujours entreposer la laveuse à 
pression dans un endroit où la température ne sera 
pas inférieure à 0 °C (32 °F).  La pompe sur cette 
machine est susceptible de subir des dommages si 
elle est exposée au gel.  LES DOMMAGES DUS AU 
GEL NE SONT PAS COUVERTS PAR LA GARANTIE.

1.

Stop the pressure washer, squeeze spray gun 
trigger to release pressure.

2.

Detach water supply hose and high pressure hose.

3.

Turn on the machine for a few seconds, until  
remaining water exits. Turn motor off immediately.

4.

Drain the fuel from the fuel tank.

5.

Do not allow high pressure hose to become kinked.

6.

Store the machine and accessories in a room 
which does not reach freezing temperatures.

CAUTION: Failure to follow the above directions 
will result in damage to your pressure washer.

Attention : Le non-respect des directives ci-dessus 
entraînera des dommages à la laveuse à pression.

When the pressure washer is not being operated or is 
being stored for more than one month, follow these 
instructions:

1.

Replenish pump oil to upper level.

2.

Drain fuel from fuel tank, fuel line and filter.

3.

Cover the pressure washer and store in a clean, 
dry place that is well ventilated away from open 
flame  or sparks.

After Extended Storage

CAUTION: Prior to restarting, thaw out any 
possible ice from pressure washer hoses, 
spray gun or wand.

Attention : Avant de redémarrer, faire fondre la 
glace se trouvant sur les boyaux, le pistolet pulvéri-
sateur ou la lance de la laveuse à pression.

Karcher HDS 505, 508, 509, 510  Operator’s Manual  9.800-078.0 - R

Содержание 1.575-505.0



















































Отзывы: