Kannad 406 AF Скачать руководство пользователя страница 50

Страница: 50 / 52

INSTALLATION MANUAL OPERATION MANUAL INSPECTION LOG

KANNAD 406 AF / AF-H / AF (6D)

PAGE: 602

JUN 23/2008

C. Battery replacement

Battery replacement is mandatory:

• after more than 1 hour of real transmission (cumulated duration);
• before or on the battery expiration date.

Battery available from any KANNAD distributor or dealer.

KANNAD

Z.I. des Cinq Chemins BP23

56520 GUIDEL - FRANCE

Telephone: +33 (0)2 97 02 49 49 Fax: +33 (0)2 97 65 00 20

Web:

http://www.kannad.com

- E-mail:

contact.aviati [email protected]

Support:

[email protected]

Tel.: +33 (0)2 97 02 49 00

List of distributor available on our Web site:

http://www.kannad.com

Only original battery pack included in battery kit

(KIT BAT 300, P/N S1820516-99)

supplied by KANNAD can be installed.

KANNAD refuse all responsibility and invalidate

all warranty should other packs be installed.

Содержание 406 AF





















































Результаты поиска

Содержание 406 AF

Отзывы:

Похожие инструкции для 406 AF

Бренды по названию

Популярные бренды

Kannad 406 AF, Инструкция по установке, Руководство по эксплуатации, Журнал осмотров

Результаты поиска

Содержание 406 AF

Отзывы:

Похожие инструкции для 406 AF

Бренды по названию

Популярные бренды