manualshive.com logo in svg

Kanmor Zone Control 369e, Руководство пользователя

Поделиться
Скачать
Kanmor Zone Control 369e Скачать руководство пользователя страница 1

- Data Brochure

Zone Control 369e

D 369e

06/03

 

1 of 32 

© 2003  

D 369e - 06/03

The Zone Control 369e is designed to control the temperature in up to six heating zones using Room Temperature Units (RTUs) 
or indoor sensors. The 369e allows one stage heating zones, two stage heating zones, or a combination of one stage and two 
stage heating zones. PID zoning logic allows for a staggering and synchronization of multiple zones in order to minimize boiler 
short cycling. The 369e is capable of operating a single cooling output and can provide automatic or manual heat / cool change 
over. When the 369e is used with a kanmor Integrated System Control, the 369e provides indoor temperature feedback that 
automatically adjusts the supply water temperature in order to satisfy the zone with the highest heat load. A large Liquid Crystal 
Display (LCD) is incorporated in order to view system status and operating information. The LCD and user key pad are used to set 
the control’s adjustments and to monitor zone running times, outdoor high and low temperatures, minimum zone temperatures, 
and many other useful items.

Additional features include:

• Control Schedule
• Individual Zone Schedules
• Optimum Start / Stop
• Cooling Control or Cooling Enable
• Manual Override

• Slab Minimum and Slab Maximum Temperature Control
• Remote Display and Adjustment Capabilities
• Test Sequence to Ensure Proper Component Operation
• 230 V (ac) Power Supply
• CE Approved

Output

Zone Pumps or Zone Valves

Output

System

Pump

Output

Cooling

Input

Indoor
Sensor

Input

Indoor
Sensor

or

Input

Room
Temperature
Unit (RTU)

Input

Room
Temperature
Unit (RTU)

Input

Remote
Display
Module

Input

Indoor

Sensor

Input

Room

Temperature

Unit (RTU)

Input

Room

Temperature

Unit (RTU)

Input

230 V (ac)

Power

Supply

Input

Timer

Optional

Input

Outdoor

Sensor

Included

Input

Zone

Control

Output

Integrated

System

Control

Do not apply power

Do not apply power

Out

Sw

In

1

2

2

3

4

4

5

6

6

Out

Com tN1 tN1

2

Zn

3

Zn

1

Zn

1-2

Com

3-4

Com

4

Zn

5

Zn

Indr Com tN1 tN1

1

3

5

2

4

8 9

6 7

10

20 21 22 23 24 25 26

Indr

27

Com

28

tN1/2

29

tN1

30

Indr

31

UnO Zo

Zo Com

H1

2XXA

5-6

6

Com Zn

Pmp

L

N

Sys

13 14

11 12

15 16

17 18

19

Cooling

Power

Zone Control 369e

Six Zones

Menu

Item

View

°

C

Made in Canada

Power
Relays

Signal wiring must be rated at least 300 V.

not testing
testing
testing paused

WARNING: battery may explode
or cause burns if disassembled,
recharged or exposed to fire or 
high temperatures.

Lithium Battery CR1620
POS (+) up

Press here
on battery to
remove it.

INSTALLATION CATEGORY II

Test

None

Setback

off
red
red

 

230 V 

±

10% 50/60 Hz 1200 VA

 

230 V (ac) 5 A 1/4 hp, pilot duty 240 VA

Input

Room
Temperature
Unit (RTU)

Input

Room
Temperature
Unit (RTU)

M

OR

M

OR

M

OR

M

OR

M

OR

M

OR

Содержание Zone Control 369e

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды