manualshive.com logo in svg

Kangook Cors-Air Black Bull, Руководство пользователя

Получите бесплатное руководство пользователя для парашютного крыла Kangook Cors-Air Black Bull на нашем сайте. Скачайте его сейчас, чтобы получить подробные инструкции по использованию этого продукта. Не забудьте загрузить его с manualshive.com.

Поделиться
Скачать
background image

11 

 

   Kangook Paramotors User Guide –  

 

 

February 2020 – V3.0  

 

        Copyright 2020 All Rights Reserved.   

3.

 

Harness and Frame System 

 

Kangook Paramotor

 frames have been specially designed to use the all features of 

the Sup’Air El Comfort harness. This system accommodates the full range of options 
when choosing one of the 6 different attachment systems offered by 

Kangook

. 

The following steps must be done on both sides of the frame.  

  

A 

1 : Kangook Komfort harness. 

2 : Place the harness against the frame and 

pass the strap under the hoop. 

3 : Loop back around the hoop and insert 

the strap into A. 

4 : Insert the strap into B without 

tightening it (see picture 4). 

B

 

Содержание Cors-Air Black Bull

























































Отзывы:

Нет отзывов

Похожие инструкции для Cors-Air Black Bull

Бренды по названию

Популярные бренды

Загрузить еще бренды