K&K Sound Pure Mini Скачать руководство пользователя | Manualshive

Страница: 4 / 24

background image

4

1. PACKAGE CONTENTS

• 3 transducers with cable harness and endpin jack.

The Pure Mini uses 3 identical transducers. It does
not matter in which position (high e/b string, g/d
string, low e/a string) you install them.

• Manual
• Accessories pack (see photo, from left to right)

•  Jig (remove protective foil before use)
•  White pin & golf tee
•  Putty (remove protective foil before use)
•  Double-sided tape for peel-and-stick install

2. TOOLS/SUPPLIES NEEDED

• Superglue gel (any brand of Cyanoacrylate glue will

do as long as it is gel)

• Electric drill (for endpin jack mount)
• Drill bits, at least 3/8” (10mm) and ½” (12mm for

endpin jack mount), endpin reamer or ½” Forstner
bit

• Pliers or wrench for endpin jack installation

«
...
2
3
4
5
6
...
»

Содержание Pure Mini

























Отзывы:

Нет отзывов

Похожие инструкции для Pure Mini

Бренд: PAT Страницы: 55

Бренд: PAT Страницы: 31

Бренд: Veris Industries Страницы: 2

Бренд: Yamaha Страницы: 69

Бренд: Kawai Страницы: 142

Бренд: Kawai Страницы: 10

Бренд: C-LOGIC Страницы: 4

Бренд: Abus Страницы: 2

Бренд: babymoov Страницы: 12

Бренд: BabyOno Страницы: 24

Бренд: babymoov Страницы: 4

Бренд: Calsense Страницы: 4

Бренд: Calsense Страницы: 6

Бренд: Campbell Страницы: 64

Бренд: Campbell Страницы: 42

Бренд: Campbell Страницы: 19

Бренд: Campbell Страницы: 26

Бренд: Campbell Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды