Kanardia miniDaqu Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 53

Kanardia miniDaqu Скачать руководство пользователя страница 15

miniDaqu — Manual

2.1

General Rules

2.1

General Rules

Daqu shall be installed close to the engine in order to keep the sensor cables
short. This can save significant weight on cables.

It may be installed on the engine side of the firewall providing that it is not
under direct influence of engine and/or exhaust heat.

The orientation or position of Daqu is not critical. Just make sure that Daqu
connectors are easily accessible and sensor cables are guided properly. A good
access to sensor connectors significantly simplifies the wiring, troubleshooting,
service and maintenance.

Daqu must NOT be mounted directly on the motor or on a place where
significant vibrations may occur.

Daqu is not waterproof. Significant measures were made to protect Daqu
electronics from moisture, but direct contact with fluid will cause invalid
sensor readings or even permanent failure. So when you install Daqu in engine
compartment, make sure that Daqu will not be exposed to fluids or moisture.
Do not put Daqu under coolant expansion bottle.

Please consider that flying trough rain delivers vast amount of water into
engine compartment. If Daqu is in engine compartment, please make sure
that this water will not reach it. If you intent to fly trough rain, the best way
is to enclose Daqu with watertight compartment.

Daqu is not shipped with the mounting hardware. You may use any appro-
priate removable fittings that suit the need – just do not use rivets.

2.2

Connectors and Cables

Power, CAN and ECU connector details are presented in this section. Sensor
connectors are described in a separate chapter.

Mini Daqu has two D-SUB 9 connectors as shown on figure 3.

The left

connector is used to connect mini Daqu to Kanardia CAN bus, which also
supplies power. The right connector is used to connect mini Daqu to engine
ECU, Rotax iS for example.

The 12 pin connector on top is used to connect additional sensors and probes.

2.2.1

Kanardia CAN Bus Connector

This connector is used to connect Daqu to Kanardia CAN bus system. It also
brings power for Daqu at the same time. On the Daqu cable side, a male

13

©

Kanardia

2019-2022

«
...
13
14
15
16
17
...
»

Содержание miniDaqu






















































Отзывы:

Нет отзывов