background image

Combo — Manual

3.3

Toggle Illumination Knob

3. Turn the knob to 1013 hPa (29.91 inHg) to complete the proce-

dure. Observe the units and values next to QNH. They changed
from hPa to inHg and vice versa.

3.3

Toggle Illumination Knob

1020

1035

1013 for hPa or 30

.

12

30

.

56

29

.

91 for inHg.

This section applies only to instruments without push/rotate knob.

If the external illumination knob does not work – screen does not re-
act on the knob, try the following procedure. This procedure enables
remote illumination knob if it was not enabled or disables illumina-
tion knob, if it was enabled.

1. Turn QNH until it shows 1020 hPa (30.12 inHg) and wait for

about three seconds for a short cyan line to appear on top of
LCD display.

2. Quickly turn the knob to indicate 1035 hPa (30.56 inHg). A

moment later a longer cyan line appears.

3. Turn the knob to 1013 hPa (29.91 inHg) to complete the pro-

cedure.

4. Finally, you need to turn off Indu Combo and then back on in

order to activate the change.

4

Maintenance & Repair

No special maintenance is required.

The instrument has no serviceable parts inside. In the case of mal-
function, it must be sent to factory for a repair.

16

©

Kanardia

2015-2018

Содержание INDU COMBO


























Отзывы: