Kamstrup flowIQ 3100 Series Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 68

Kamstrup flowIQ 3100 Series Скачать руководство пользователя страница 54

TECHNICAL DESCRIPTION flowIQ® 3100

54

Kamstrup

A/S • Technical Description •

5512-1242_N

1_GB •

10.2019

17.11

Legal changes outside seal

This paragraph describes the legal changes, which can be carried out without disassembling the meter and
thereby breaking the legal seal.

All legal changes are fully traceable in an adjust log, which cannot be deleted. The number of legal changes
appears from the display (see paragraph

Adjustment mark

). Maximum 9 changes are possible.

The adjust log can only be deleted if the meter is disassembled and the legal seal is broken.

It appears from the meter’s software version whether a specific meter can be reset outside the legal seal.

See

support of legal changes below:

SW revision

Re-adjustment

Reset

A1

B1

–

F1

✓

G1

–

>

✓

✓

✓

= supported

17.11.1

Flow adjustment

The meter is initially verified from the factory. A new factory adjustment requires disassembling of the meter
and can only be carried out by Kamstrup A/S. When the meter has been locked it is only possible to make a
percentage correction of the flow curve at three individual points. This is called re-adjustment.

17.11.2

Re-adjustment

A re-adjustment can be made without disassembling the meter and thereby breaking the legal seal. The following
restrictions apply:

- Maximum 9 (nine) re-adjustments are possible.

- Maximum adjustment compared to the factory adjustment is +/-10%.

- Each readjustment is logged in the meter.

During a re-adjustment the flow curve is corrected at three fixed points and the curve will be re-adjusted to these
new points.

IMPORTANT: The laboratory, which makes the readjustment, must attach an adjustment label with the valid

adjustment number to the meter. Naturally, this number must be identical with the number (AX) in the meter’s

display.

17.11.3

Reset

The  meter  can  be  reset  via  the  optical  eye.  This  is  used  in  connection  with  re-verification  by  authorized
laboratories. All loggers and registers including the legal volume register are reset. Only the adjust log and the
clock  are  not  reset.  At  the  same  time  the  meter  is  set  to  transport  mode  and  the  radio  is  switched  off.  The
following restrictions apply to reset:

- The meter can maximum be reset 9 times.

- Each reset is logged in the meter.

IMPORTANT: The laboratory, which resets the meter, must attach an adjustment label with the valid adjustment
number to the meter. Naturally, this number must be identical with the

number (AX) in the meter’s display.

«
...
52
53
54
55
56
...
»

Содержание flowIQ 3100 Series





































































Отзывы:

Нет отзывов