background image

Changing the pump settings

Note

It is recommended that the pump runs at constant
pressure when used for underfloor heating. The factory
setting of the pump is not set to constant pressure and
must therefore be changed

The pump (Grundfos UPM3) has to be set to the constant pressure
modus (Δp-c) to enable an optimal operation of the underfloor
heating system.

The settings are done on the pump house as described below.

Pump settings

Note

Leave the pump on the selected program. It goes back
into operation automatically and has saved the settings.

Enable
setting

Press
and
hold,
sec

Factory setting

Underfloor
heating
constant
pressure

Step

4

2 x

1

4

3 x

2

4

4 x

3

Pump effect

EEI ≤ 0.20 Part 3

Value

Speed

P

1

 [W]

Min.

2

Max.

33

Pump operation

Display view

Operation settings

0 % 

 P1 

 25 %

25 % 

 P1 

 50 %

50 % 

 P1 

 75 %

75 % 

 P1 

 100 %

Pump alarms

Display view

Alarm status

Blocked

Low voltage

Electrical fault

6.3 Combi Port E mobile

application

The Combi Port E controller has preset default settings and is only
operated via the app. Likewise, all settings for domestic water and
heating are made via the app.

Combi Port E app

PDF

SI0000301

1.

Download the Combi Port E app. It is available both for iOS and
Android mobile devices.

2.

Scan the QR code available on the Combi Port E controller.

3.

Press the blue button in the middle of the Combi Port E
controller until it flashes. Continue in the App.

4.

Helptexts and guidance is available in the app.

5.

The app consists of three different user levels. Access is given
by activating the received code.

6.

Fill in the code in menu "Settings".

7.

Reconnect the controller to get the new level (push A, see
below).

App advantages

Display with live update of values, e.g. flow, temperature etc

Software updates available (customer service only)

Daily evaluation directly to service

Commissioning protocol (content of all set points and operating
modes)

App structure

Overview

CD0000321

Uponor Combi Port E

Standby

Hot water

Standby

Circulation

Standby

Supplier

Operation

Heating

System

Uponor Combi Port E

Standby

Hot water

Standby

Circulation

Standby

Supplier

Operation

Heating

System

Android

iOS

C

D

E

F

G

Configuration

Settings

Special functions

B

A

B

16 

 |  

Combi Port E D

  |  

Installation and operation manual

Содержание uponor Combi Port E D





































Отзывы: