KAESER M27 Скачать руководство пользователя | Manualshive

Страница: 139 / 294

background image

Battery replacement

If the battery is to be replaced, the new battery should have the same capacity, current rating and

shape as the original battery.
➤ Always replace a battery with one of the same type.

Old batteries are hazardous waste and must be disposed of correctly in accordance with local

environment protection regulations.

10.3.8 Checking the fastening of the fuel tank

The machine is equipped with a fuel tank or tanks. These are fastened with lashing strips and

ratchets.

Precondition The machine is shut down.

The machine is standing level.
The machine is fully vented, the pressure gauge reads 0 psig.
The machine is cooled down.
All compressed air consumers are disconnected and the air outlet valves are open.

The lashing strip of the fuel tank is overly tightened.

The plastic tank can be damaged by excessive tightening of the lashing strips.

The fuel tank may burst and spill.
➤ Do not overtighten the lashing strips.
➤ Slightly hand-tighten the lashing strips.

Carry out visual check

1. Check the lashing strips for tears and fraying in the fabric, and for damages to the ratchet.

Change any damaged lashing strip immediately.

2. Check whether the lashing strips are tight with the tank and that the ratchet is closed.

If the lashing strips sits loose, or the ratchet is not closed properly, tighten the fastening.

Tightening the fastening of the fuel tank

The lashing strips are tensioned via the integrated ratchet.
The lashing strips must fit closely around the fuel tank. The tensioning force of the strips must not

exceed 10 daN (approx. 25 lbf), slightly hand-tighten only.
➤ Hand-tighten the lashing strip with the integrated ratchet and push the ratchet to the strip.

10.4 Compressor Maintenance

➤ Perform maintenance tasks according to the schedule in chapter 10.2.3.1.

10.4.1 Checking cooling oil level

The oil level is checked at the oil separator tank filling port. Oil should be visible in the port when

the filler plug is removed.

10 Maintenance

10.4 Compressor Maintenance

No.: 9_9548 05 USE

Operator Manual Screw Compressor
M27

129

«
...
137
138
139
140
141
...
»

Содержание M27







































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M27

Polar Air PRS0050001

Бренд: Eaton Compressor Страницы: 38

Бренд: Danfoss Страницы: 2

Бренд: Bush Power Страницы: 2

5-3/4" Drive AG Series

Бренд: Haskel Страницы: 24

Бренд: Atlas Copco Страницы: 94

Бренд: Atlas Copco Страницы: 114

Бренд: Atlas Copco Страницы: 114

Timeter PCS-414

Бренд: Allied Страницы: 7

Бренд: Mouvex Страницы: 24

Бренд: Sullivan-Palatek Страницы: 117

Бренд: Bambi Страницы: 12

Бренд: Daikin Страницы: 32

Бренд: California Air Tools Страницы: 16

Бренд: California Air Tools Страницы: 15

POWERplus POWX1721

Бренд: VARO Страницы: 8

Бренд: ACC Страницы: 20

Бренд: Haussmann Xpert Страницы: 31

ELECTRA-SAVER ETY99A

Бренд: Gardner Denver Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды