manualshive.com logo in svg

KAESER AIRTOWER 3C, Руководство оператора

Поделиться
Скачать
KAESER AIRTOWER 3C Скачать руководство пользователя страница 78

10.10.2  Topping off with cooling oil and carrying out a trial run

Replenishing cooling oil

A sticker on the oil separator tank specifies the type of oil used.
1.

 Compressed air!

Compressed air and devices under pressure can injure or cause death if the contained energy

is released suddenly.
➤ Depressurize all pressurized components and enclosures.

2.

 The machine could be damaged by unsuitable oil!

➤ Never mix different types of oil.
➤ Never top off with a different type of oil than already used in the machine.

3. Slowly unscrew the filler plug 

4

.

4. Top off to bring the oil to the correct level.
5. Replace the filler plug's sealing ring if necessary and screw the plug into the filler port.

Starting the machine and carrying out a trial run

1. Close the enclosure.
2. Open the user's shut-off valve between the machine and the air distribution network.
3. Start the machine and check the oil level again after about 10 minutes, topping off if necessary.
4. Switch off the machine and check for leaks.

10.11  Changing the cooling oil

Always change the oil filter and oil separator cartridge when changing the oil.

Compressed air helps to expel the oil. This compressed air can be taken either from the compres‐

sor itself or from an external source.

An external source of compressed air is necessary in the following cases :
■ The machine is not operational.
■ The machine is to be restarted after a long period of standstill.

The machine must be isolated from the compressed air network and completely vented be‐

fore undertaking any work on the pressure system.

Material Cooling oil

Cooling oil receptacle
The maintenance hose with hose coupling and shut-off valve is stowed inside the machine.

There is risk of burns from hot components and oil!
➤ Wear long-sleeved clothing and protective gloves.

10 Maintenance

10.11 Changing the cooling oil

68

Operator Manual    Screw Compressor  
AIRTOWER 3C–7.5C Tri-Voltage

9_6917 34  USE

Содержание AIRTOWER 3C





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды