manualshive.com logo in svg

KAESER KOMPRESSOREN M250, Руководство оператора, Страница: 150 / 426

Поделиться
Скачать
KAESER KOMPRESSOREN M250 Скачать руководство пользователя страница 150

10.4.9  Engine belt maintenance

Defective engine belts may tear. A torn engine belt no longer drives the coolant pump and the al‐

ternator. The engine may overheat and be damaged.

Material Ratchet

Socket
Spare part

Precondition The machine is switched off.

The machine is fully vented, the pressure gauge reads 0 psig.
The machine has cooled down.
All compressed air consumers are disconnected and the air outlet valves are open.
The «battery isolating switch» is turned off.

Beware of rotating pulleys and moving belts.

There is danger of serious injury from pinching.
➤ Never check the drive belt unless the engine is at standstill.

➤ Open all doors.

10.4.9.1 Carry out visual check

1. Check the belt thoroughly for cracks, fraying or stretching.

When damaged or worn: Replace the drive belt immediately.

2. Turn on the «battery isolating switch».
3. Close the doors.

10.4.9.2 Replacing the engine belt

If the engine belt is torn or exhibits damage, it must be replaced.

Belt-tensioning device is under spring force!

Risk of lacerations or pinching when loosening or tightening the device.
➤ Take great care when working on the tensioning device.
➤ Ensure exact handling of the tool.

10 Maintenance

10.4 Engine maintenance

136

Operator Manual    Screw Compressor  
M250  SIGMA CONTROL MOBIL

No.: 9_9570 07 USE

Содержание M250











































































































































































































































































































































































































































Отзывы:

Нет отзывов