Kaden KCI36 Скачать руководство пользователя страница 15

Kaden Installation Manual  | 

15

5. Outdoor unit installation

Install the unit by following local codes and regulations. They 
may differ slightly between different regions.

Installation instructions – 

Outdoor unit

Step 1: Select installation location

Before installing the outdoor unit, you must choose an 
appropriate location. The following are standards that will help 
you choose an appropriate location for the unit.

Proper installation locations meet the following standards:

Meets all spatial requirements shown in installation space
requirements above.

Good air circulation and ventilation.

Firm and solid – the location can support the unit and will
not vibrate.

Noise from the unit will not disturb others.

Protected from prolonged periods of direct sunlight or rain.

Where snowfall is anticipated, raise the unit above the base
pad to prevent ice build-up and coil damage. Mount the
unit high enough to be above the average accumulated
area snowfall. The minimum height must be 45cm above
the base pad.

DO NOT install unit in the following locations:

Near an obstacle that will block air inlets and outlets.

Near a public street, crowded areas, or where noise from
the unit will disturb others.

Near animals or plants that will be harmed by
hot air discharge.

Near any source of combustible gas.

In a location that is exposed to large amounts of dust.

In a location exposed to a excessive amounts of salty air.

Special considerations  

for extreme weather

If the unit is exposed to heavy wind:

Install unit so that air outlet fan is at a 90° angle to the 
direction of the prevailing wind. If needed, build a barrier in 
front of the unit to protect it from extremely heavy winds.  
See figures below.

If the unit is frequently exposed to heavy rain or snow:

Build a shelter above the unit to protect it from the rain or 
snow. Be careful not to obstruct air flow around the unit.

If the unit is frequently exposed to salty air (seaside):

Use outdoor unit that is specially designed to resist 
corrosion.

600mm 

above

200mm from 

back wall

300mm 

on left

600mm 

on right

2000mm 

in front

Strong 

wind

Strong 

wind

Strong 

wind

Содержание KCI36

































Отзывы: