manualshive.com logo in svg

Kaba Access manager 92 32, Техническое руководство

"Kaba Access Manager 92 32" - Техническое руководство для управления доступом в комплекте с продуктом. Бесплатное скачивание данного руководства возможно на manualshive.com. Получите подробную информацию о настройке и использовании продукта, ознакомившись с руководством. Управление доступом никогда не было проще с "Kaba Access Manager 92 32".

Поделиться
Скачать
background image

Technical Manual

Installation

39

04045524 - 08/2016

Kaba access manager 92 32

5.7.6.6 Status display

Below the terminals for the outputs, there are light emitting diodes for status display
of the outputs.

The current status of the outputs is indicated as follows.

Designation

Signal

Meaning

REL1-3

Off

Relay is not pulled-in

lit green

Relay is pulled-in

Содержание Access manager 92 32






















































Отзывы:

Нет отзывов

Похожие инструкции для Access manager 92 32

Wasp WDT 3200 Product Reference Manual preview
WDT 3200
Бренд: Wasp Страницы: 28
Hand Held Products IMAGETEAM 3800i Application Note preview
IMAGETEAM 3800i
Бренд: Hand Held Products Страницы: 32
Themis TS-150 Quick Manual preview
TS-150
Бренд: Themis Страницы: 2
McIntosh MR-55 Instruction Manual preview
MR-55
Бренд: McIntosh Страницы: 18
Aiwa CT-X418 Operating Instructions Manual preview
CT-X418
Бренд: Aiwa Страницы: 16
Microtech PCD-47 User Manual preview
PCD-47
Бренд: Microtech Страницы: 35
Datalogic PowerScan Area Imager Quick Reference Manual preview
PowerScan Area Imager
Бренд: Datalogic Страницы: 44
Allegion Interflex IF-73 Manual preview
Interflex IF-73
Бренд: Allegion Страницы: 9
Acard AEC-67160M Ultra160 User Manual preview
AEC-67160M Ultra160
Бренд: Acard Страницы: 25
P.Lindberg 9053256 Original Manual preview
9053256
Бренд: P.Lindberg Страницы: 38
Sunrich Tech U-1000 User Manual preview
U-1000
Бренд: Sunrich Tech Страницы: 11
Hama 62753 User Manual preview
62753
Бренд: Hama Страницы: 10
Jensen MP6512i Installation And Operation Manual preview
MP6512i
Бренд: Jensen Страницы: 30
Legacy LCDCS94 Instruction Manual preview
LCDCS94
Бренд: Legacy Страницы: 6
Franklin MOVIEVIEWS FLX-110 User Manual preview
MOVIEVIEWS FLX-110
Бренд: Franklin Страницы: 22
GlobespanVirata ISL39200M Oem Installation Manual preview
ISL39200M
Бренд: GlobespanVirata Страницы: 12
Diamond Multimedia SM56PCI Quick Start Manual preview
SM56PCI
Бренд: Diamond Multimedia Страницы: 6
National Instruments PCI-232/2 Getting Started preview
PCI-232/2
Бренд: National Instruments Страницы: 64

Бренды по названию

Популярные бренды

Загрузить еще бренды