background image

2                                                                                                                    For Professional Technical Support call 1-844-242-2475 

 

PERFORMANCE 

 

Model 

HP 

GPM of Water @ Total Feet of Lift (high speed) 

Max. 

Lift 

0 ft. 

10 ft. 

20 ft. 

30 ft. 

40 ft. 

50 ft. 

PPI10001SPK 

75.0 

68.0 

56.0 

43.3 

25.0 

48 ft. 

PPI15001SPK 

1-1/2 

96.0 

86.0 

76.0 

64.0 

50.0 

32.0 

65 ft. 

 

Model 

HP 

GPM of Water @ Total Feet of Lift (low speed) 

Max. 

Lift 

0 ft. 

10 ft. 

20 ft. 

30 ft. 

40 ft. 

50 ft. 

PPI10001SPK 

37.0 

15.0 

13 ft. 

PPI15001SPK 

1-1/2 

48.0 

27.0 

17 ft. 

 

SAFETY INSTRUCTIONS 

 

1. 

DANGER

Risk of suction entrapment. Always turn off all power to the pool pump before installing the cover or 

working on any suction outlet. This pump produces high levels of suction and creates a strong vacuum at the 
main drain at the bottom of your pool or spa. This suction is so strong that it can trap adults or children under 
water if they come in close proximity to a pool or spa drain or a loose or broken drain cover or grate. Stay off the 
main drain and away from all suction outlets! 

2. 

DANGER

Risk of suction entrapment. The use of unapproved covers or allowing use of the pool or spa when 

covers are missing, cracked or broken can result in body or limb entrapment, hair entanglement, body 
entrapment, evisceration and/or death. Limb Entrapment: When a limb is sucked or inserted into an opening 
resulting in a mechanical bind or swelling. This hazard is present when a drain cover is missing, broken, loose, 
cracked or not properly secured. Hair Entanglement: When the hair tangles or knots in the drain cover, trapping 
the swimmer underwater. This hazard is present when the flow rating of the cover is too small for the pump or 
pumps. Body Entrapment: When a portion of the body is held against the drain cover trapping the swimmer 
underwater. This hazard is present when the drain cover is missing or broken, or the cover flow rating is not high 
enough for the pump or pumps. Evisceration/Disembowelment: When a person sits on an open pool (particularly 
a child wading pool) or spa outlet and suction is applied directly to the intestines, causing severe intestinal 
damage. This hazard is present when the drain cover is missing, loose, cracked, or not properly secured. 
Mechanical Entrapment: When jewelry, swimsuit, hair decorations, finger, toe or knuckle is caught in an opening 
of an outlet or drain cover. This hazard is present when the drain cover is missing, broken, loose, cracked, or not 
properly secured. 

NOTICE

: All suction plumbing must be installed in accordance with the latest national and local codes for 

swimming pools, spas and hot tubs, including NSPI standards and CPSC guidelines. 

3. 

DANGER

Risk of electric shock. Can shock, burn or kill. Connect only to a branch circuit protected by a ground-

fault circuit-interrupter (GFCI). Contact a qualified electrician if you cannot verify that the circuit is protected by a 
GFCI. This unit must be connected only to a supply circuit that is protected by a ground fault circuit-interrupter 
(GFCI). Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the 
GFCI, push the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If 
the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without 
the test button being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use 
this pump. Disconnect the pump and have the problem corrected by a qualified service representative before 
using. 

Содержание PPI10001SPK














Отзывы: