K-TRON KSU-II/KCM страница 78 Скачать руководство пользователя

Страница: 78 / 121

Alarm Messages- Cause and Remedy

4.6 Massflow variances in LWF feeding

Page 78

Docu-No.: 0590020601-EN Rev. 1.6.0

4.6

Massflow variances in LWF feeding

Alarms

Cause

Remedy

General massflow
fluctuations LWF

• Vibrations and drafts on feeder.



Improve the location of the scales.

– Reduce the <CTRL GAIN> in the

<TUNING> menu.

– Increase the filter length display in

program parameter <TUNING>
menu, <DISPLAY FILTER

– Increase the tolerance limit in

program parameter <ALARM>
menu, <MF ERR+/->.

– Protect the feeder from drafts and

air currents.

• Irregular discharge.



Install different feeder screws when
operating at low feeder-screw
speeds.



Check for material flow problems
such as bridging in the feeder
hopper.

• Irregular motor speed.



Re-enter start feeding factor <INIT
FF> in the <PRODUCT CHANGE>
menu and check in volumetric
mode if the speed is constant.

Is the speed constant?

If so:



Re-calibrate the new feeding
factor, reduce the <CTRL GAIN> in
the <TUNING> menu, if necessary.

If not:



Check the motor setting and the
pick-up: verify the discharge feeder
screws are not bound.

• Friction on the scales

(to be ascertained with a static
weight test).



Check all mechanical connections
to the scale, they must be flexible.
The scale may not touch anything.



Replace scale.

Table page 1 of 2

Содержание KSU-II/KCM


























































































































Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды

K-TRON KSU-II/KCM, Инструкция по программированию

Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды