K-TRON KSU-II/KCM страница 45 Скачать руководство пользователя | Manualshive

Страница: 45 / 121

background image

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 45

Programming Reference

1

Machine setup menu 1.7

1.7.12

Performance sub-menu

Depending upon drive type, certain parameters will not be displayed.

Parameter

Definition

CONTROL-%

Control-%

This parameter is a quality indicator of loss-in-weight feeding
performance. This value uses the same technique like the pert value
calculation in relation to the setpoint where 100% means no noise,
0% means too much noise. If the controller is in volumetric or pert,
the value is slowly decreased.

A value > 80% means usually a good performance.

GRAV RATIO-%

Gravimetric Ratio-%

The time ratio the machine runs in gravimetric mode and has no pert
disturbance. The value is filtered with a time constant of 15 minutes.

A value of 100% means the feeder is always in gravimetric mode and
shows no Pert disturbance while 0% means the feeder is never in
Gravimetric mode.

INT CHANNEL-%

Internal Channel-%

The internal channel performance is calculated in two parts, the
bandwidth load and the error counter where it considers 10 errors
per minute as bad and 100% load as bad. Both values are taken in
square as follows:

IntChanPrf% = 100 * 1 - [(Load² + (0.1*Err/min)²) /2]

Example: 5 errors/min and 50% load = 75% performance.

Expect normal values of 75% to 99%.

KCM TEMP [deg C]

KCM Temperature

Displays the actual temperature in the KCM in °C.

Input range: Display only.

TORQUE-%

Only for DC motor and stepper

motor drives

Torque-%

The motor torque is derived from the power indication according to
the following formula:

Torque = 100*(actual power * nominal speed) / (nominal power *
actual speed).

Notes:

• On low speeds, this indication might be inaccurate.

• 100% torque is the maximum allowed.

• Not for vibratory feeders or for AC Drive Interface.

• At low speeds, torque will reach a maximum of 100% before

<Actual Power> reaches <Maximum Motor Power>. At high
speeds, the opposite will occur.

Table page 1 of 2

«
...
43
44
45
46
47
...
»

Содержание KSU-II/KCM


























































































































Отзывы:

Нет отзывов

Похожие инструкции для KSU-II/KCM

Relion 670 series

Бренд: ABB Страницы: 760

Бренд: ABB Страницы: 128

Бренд: D-Link Страницы: 40

Бренд: 7bit Страницы: 2

Бренд: Jafar Страницы: 15

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

PowerXL DX-NET-ETHERCAT-2

Бренд: Eaton Страницы: 3

Бренд: Galaxy Control Systems Страницы: 5

Бренд: GCE Страницы: 24

Бренд: Quectel Страницы: 95

Бренд: ICAS Страницы: 51

Бренд: Icar Страницы: 40

Бренд: Icar Страницы: 86

Бренд: Icar Страницы: 39

Бренд: IBP Страницы: 12

Бренд: Kathrein Страницы: 16

Бренд: Lawler Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды