K-TRON KSU-II/KCM страница 37 Скачать руководство пользователя | Manualshive

Страница: 37 / 121

background image

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 37

Programming Reference

1

Machine setup menu 1.7

1.7.4

Motor sub-menu

The motor sub-menu is shown for four types of drives.

• DC drives for 450 and 1600 watts

• AC interface drive

• Vibratory drive

• Stepper motor drive in three versions

1.7.5

Motor sub-menu for DC motor

Some parameters will not be displayed for every drive case. T

Parameter

Definition

GEAR REDUC

Gear Reduction or Total

Gear Reduction

This parameter is used if the Screw Modulation or the Auto Gear
Reduction functions are used. This entry must be the total reduction
value between the drive motor and the feed screw. This entry is the
lowest reduction or simply provides the highest screw speed for any
given motor rpm.

Input range: 0 to 999

Default: 0

GEAR REDUC L

Gear Reduction Low

This parameter is used if the Auto Gear Reduction function is used.
This entry must be the total reduction value between the drive motor
and the feed screw. This entry is the highest reduction or simply
provides the lowest screw speed for any given motor rpm. This entry
is checked against the GEAR REDUC value to be sure that the
magnitude of the entry is correct.

Input range: 0 to 999

Default: 0

PICK UP TEETH

Speed Pickup Teeth

Input of the number of teeth on the pick up gear.

This gear is used for measuring the speed.

Input range: 0 to 9999

Default: 120

ACTUAL POWER-[watts]

Actual Motor Power

Displays the actual consumed motor power.

Input range: Display only [W]

MAX. MOT POWER-

[watts]

Max Motor Power

This entry sets the maximum output power to the motor.
(See nameplate on motor for value)

Input range: 25 to 1600 W

Default: Depends upon installed drive

MAX MOT VOLTAGE

Motor Voltage

This entry sets the maximum output voltage to the motor.
(See nameplate on motor for value)

Input range: 90 to 220 Vdc Default: 180 Vdc

Table page 1 of 2

«
...
35
36
37
38
39
...
»

Содержание KSU-II/KCM


























































































































Отзывы:

Нет отзывов

Похожие инструкции для KSU-II/KCM

Бренд: QUAD Страницы: 16

SmartSwitch 6000

Бренд: Cabletron Systems Страницы: 76

Бренд: Gascat Страницы: 32

Бренд: Laars Страницы: 28

EP Series Pro-Bloc

Бренд: Parker Страницы: 11

Бренд: Parker Страницы: 22

Бренд: Parker Страницы: 2

Бренд: Full Gauge Controls Страницы: 3

Бренд: Bender Страницы: 28

Бренд: Hirschmann Страницы: 48

Бренд: Nibe Страницы: 84

Бренд: IBC control Страницы: 16

eTracer ET4415BND

Бренд: Epsolar Страницы: 44

Бренд: Graco Страницы: 166

Infi 90 IMSPM01

Бренд: Bailey Страницы: 52

Бренд: Contemporary Research Страницы: 22

Smart 4 Universal

Бренд: Classic Страницы: 12

Бренд: Pilz Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды