K.H. DEWERT 2690XLE Скачать руководство пользователя страница 4

Dewert User Manual 2690XLE/2695XLE/2890XL/2895XL – Updated 11.2021/3 MDR                              Page 4 of 15 

The lying surfaces and the underframe are not anti-static as standard. 
Our products are not intended for use in wet rooms and must under no circumstances be cleaned using so-
called bed washers. This would irreparably destroy the product. 
The head part and armrests are only intended to support the patient and must not be used for sitting. 

 

If the underframe is designed with movability (optional), all the castors must always be locked before using 
the table.  

 

Do not put a damaged device into operation. 
 
Disconnect the device from the mains (power supply) in the event of a fault or during maintenance work. 
To disconnect, be sure to grasp the plug, not the power cable. 
 
This device must not be modified without the express permission of the manufacturer. 
 
When transporting the table, take hold of the underframe, 

NOT

 the upper frame. 

 
 
1.8 Model designation and type labelling 

The exact model designation depends on the choice of frame colour:  

-00 white powder coated (RAL 9010); 
-03 white aluminium powder coated (RAL 9006); 
-04 grey aluminium powder coated (RAL 9007) 

and the type of selected height adjustment:  

E = electromotive; 

 

 

 

/H = hydraulic 

 
The type plate is attached to the underframe on one long side of the table. It provides information about key 
table data. 
The following symbols are listed there (by way of example), their meanings are: 
 

 
Read the operating 
manual   

 
     Serial no. 

 
Applied part Type B  

                   
Caution, potential 
hazard 

 
Max. load 
capacity 

 
    CE mark 
 

 
Date of manufacture 

      
     Product may only  
     be used in dry  

                        rooms 

 
  Do not dispose of with  
  household waste 

 
Address of 
manufacturer 

         Protective  
         insulation,  
         protection class II 

 

 

 

1.9 Meaning of the serial number 

The serial no. is located on the type plate or shown separately next to the type plate of the table. 
This number is unique and firmly linked to this specific individual product. It enables us to identify this table 
model and trace back assemblies/safety-relevant components at any time.  
Please always state this serial number when enquiring about spare parts.  
 
 
 
 
 
 

Содержание 2690XLE
















Отзывы: