JYTEK USB-62401 Скачать руководство пользователя

Страница: 48 / 62

Operation

3.6.2

General Purpose Timer/Counter

The USB-62401 is equipped with one general purpose timer/counter

featuring:



Count up/down controllable by hardware or software



Programmable counter clock source (internal clock up to 80MHz,

external clock up to 10 MHz)



Programmable gate selection (hardware or software control)



Programmable input and output signal polarities (high active or

low active)



Initial Count loaded from a software API



Current count value readable by software without affecting cir

cuit operation.

Table 3-4: Timer/Counter Pin Definition

The timer/counter has three inputs that can be controlled via hard

ware or software, clock input (GPTC_CLK), gate input (GPTC_GATE), and

up/down control input (GPTC_UD). The GPTC_CLK input provides a clock

source input to the timer/counter. Active edges on the GPTC_CLK input

increment or decrement the counter. The GPTC_UD input directs the

counter to count up or down (high: count up; low: count down), while

the GPTC_GATE input is a control signal acting as a counter enable or

counter trigger signal in different applications. The GPTC_OUT then gen

erates a pulse signal based on the timer/counter mode set.
All input/output signal polarities can be programmed by software appli

cation. For brevity, all GPTC_CLK, GPTC_GATE, and GPTC_OUT in the fol

lowing illustrations are assumed to be active high or rising-edge

triggered.

Pin

Function

Pin

Function

GPTC_OUT0 (GPO0)

GPTC_OUT1 (GPO1)

GPTC_UD (GPI1)

GPTC_AUX (GPI3)

GPTC_CLK (GPI0)

GPTC_GATE (GPI2)

DGND

Содержание USB-62401































































Результаты поиска

Содержание USB-62401

Отзывы:

Похожие инструкции для USB-62401

Бренды по названию

Популярные бренды

JYTEK USB-62401, Руководство пользователя

Результаты поиска

Содержание USB-62401

Отзывы:

Похожие инструкции для USB-62401

Бренды по названию

Популярные бренды