JYTEK PCIe-69814 Series Скачать руководство пользователя страница 28

Страница: 28 / 34

To achieve sampling rates other than 80MS/s, a number for scan interval counter needs only

be specified. For example, if the scan interval counter is set as 2, the equivalent sampling

rate is 80MS/s / 2 = 40MS/s. If as 3, the equivalent sampling rate is 80MS/s / 3 = 26.66MS/s,

and vice versa. The scan interval counter is 16 bits in width, therefore the lowest sampling

rate is 1.221kS/s (80MS/s / 65535).

TIMEBASE

DATA

Acquisition

In Progress

Trigger

Acquisition is initiated following this clock edge

ScanIntrv = 1

D10

ScanIntrv = 2

ScanIntrv = 3

Figure 3-14: Varying Sampling Rates by Adjusting Scan Interval Counter

Counter Name

Length

Valid Value

Description

ScanIntrv

16-bit

1-65535

Timebase divider to achieve equivalent

sampling rate of the digitizer, where

Sampling rate = Timebase / ScanIntrv

DataCnt

31-bit

1-2147483647

Specifies the amount of data to be

acquired: 1 - 2147483648 for pre-trig

or mid-trig mode peration

trigDelayTicks

16-bit

1 -65535

Indicates time between a trigger event

and commencement of acquisition.

The unit of a delay count is the period

of the Timebase.

ReTrgCnt

31-bit

1-2147483647

Enables re-trigger to accept multiple

triggers.

1 - 2147483647 for normal operation
See Section 3.4.5: Acquisition with

Re-Triggering

Table 3-4: Counter Parameters and Description

Содержание PCIe-69814 Series



































Результаты поиска

Содержание PCIe-69814 Series

Отзывы:

Похожие инструкции для PCIe-69814 Series

Бренды по названию

Популярные бренды

JYTEK PCIe-69814 Series, Руководство пользователя

Результаты поиска

Содержание PCIe-69814 Series

Отзывы:

Похожие инструкции для PCIe-69814 Series

Бренды по названию

Популярные бренды