JVC SuperLoLux TK-C2301WPRU Скачать руководство пользователя страница 11

Страница: 11 / 64

Thank you for purchasing this product.

Before use, please read this “INSTRUCTIONS” and the information

materials included to ensure proper use of this product.

The instructions in this manual are for TK-C2301WPRU and TK-

C2301WPRE.

TK-C2301WPRE is not evaluated by UL.

Features

Built in high reliability IR LED

DAY/NIGHT surveillance with auto IR cut filter on/off (Color/Black and

White shooting)

3D noise reduction (3DNR)

4 areas privacy mask

Built-in display mode (CRT or LCD selectable)

Outdoor-ready vandal and tamper resistant structure (complies with

IP66)

How to read this manual

Conventions and symbols

Note

: Indicates operating precautions.

Memo

: Indicates reference data regarding limitations on

functions, usage and the like.

: Indicates a reference page or item.

Contents of this manual

JVC KENWOOD Corporation holds the copyright to this manual.

Any part or all of this manual may not be reproduced without prior

consent from the company.

Product names of other companies described in this manual are

trademarks or registered trademarks of the respective companies.

Symbols such as

, and

are omitted in this manual.

Design, specifications and other contents described in this manual

are subject to change for improvements without prior notice.

Introduction

E-11

Содержание SuperLoLux TK-C2301WPRU

































































Результаты поиска

Содержание SuperLoLux TK-C2301WPRU

Отзывы:

Похожие инструкции для SuperLoLux TK-C2301WPRU

Бренды по названию

Популярные бренды

JVC SuperLoLux TK-C2301WPRU, Инструкция по эксплуатации

Результаты поиска

Содержание SuperLoLux TK-C2301WPRU

Отзывы:

Похожие инструкции для SuperLoLux TK-C2301WPRU

Бренды по названию

Популярные бренды