JVC SuperLoLux TK-C2301WPRU Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 64

background image

Checking after Operation

A light shielding cushion is attached to the lens so that the lens is not

exposed to infrared light directly. After adjustment, when attaching the

dome cover and the lens cover, make sure that the light shielding

cushion is attached correctly with the taper (tilted) side facing up (refer

to the figure below).

If the light shielding cushion is not attached correctly or deformed,

infrared light reaches to the lens, causing the recorded images to look

shiny white.

.

Taper (tilted)

Light shiedling cushion

<Light shielding cushion attached
correctly>

Light shiedling cushion

Adjustment

E-39

«
...
37
38
39
40
41
...
»

Содержание SuperLoLux TK-C2301WPRU

































































Отзывы:

Нет отзывов

Похожие инструкции для SuperLoLux TK-C2301WPRU

Бренд: UEi Страницы: 6

Бренд: Q-See Страницы: 141

Бренд: Q-See Страницы: 12

Бренд: Camera Страницы: 13

Бренд: Olympia Страницы: 40

Бренд: IDTECK Страницы: 57

Бренд: Baldwin Boxall Страницы: 7

Бренд: RUD Страницы: 6

Бренд: dallmeier Страницы: 40

Бренд: Brilix Страницы: 37

Бренд: Niko Страницы: 175

Бренд: Basler Страницы: 2

Бренд: Smartec Страницы: 29

DH-IPC-HF8835FN

Бренд: Dahua Страницы: 20

Бренд: Veilux Страницы: 47

Бренд: Defender Страницы: 17

Бренд: Axis Страницы: 71

Бренд: Navigator Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды