JVC SuperLoLux TK-C2301WPRU Скачать руководство пользователя страница 32

Страница: 32 / 64

Mounting the Camera (Continued)

Mounting the Camera Using the Conduit Hole at the Side of the

Base

If the camera cannot be mounted directly to the ceiling, use the conduit

hole at the side of the base to mount the camera to the pipe.

Conduit hole: G3/4-14 UNC (TK-C2301WPRU), M25 (TK-C2301WPRE)

Remove the dome cover and inner dome (

page 23)

Remove the camera unit from the base and mount the fall

prevention wire to the camera unit

Refer to "Mounting the Camera Using the Conduit Hole at the Bottom of

the Base" (

page 30) step 2.

Wind the sealing tape

Wind the sealing tape around the pipe junction (where the conduit hole

thread lines with the pipe screw hole) two or more times.

Remove the conduit plug from the base

Loosen the mounting screw (M3 x 6 mm) using a flathead screwdriver

and remove the conduit plug at the side of the base.

Mount the conduit plug that was removed to the conduit hole at

the bottom of the base

Mount the base to the pipe

Screw the pipe to the conduit hole at the side of the base.

Note

When screwing the pipe, do not screw beyond 12 mm. Doing

so can damage the camera interior.

Sealing tape

Mounting screw

Conduit plug

Refer to "Mounting the Camera Using the Conduit Hole at the

Bottom of the Base" (

page 30) step 6 to 9

Installation

E-32

Содержание SuperLoLux TK-C2301WPRU

































































Результаты поиска

Содержание SuperLoLux TK-C2301WPRU

Отзывы:

Похожие инструкции для SuperLoLux TK-C2301WPRU

Бренды по названию

Популярные бренды

JVC SuperLoLux TK-C2301WPRU, Инструкция по эксплуатации

Результаты поиска

Содержание SuperLoLux TK-C2301WPRU

Отзывы:

Похожие инструкции для SuperLoLux TK-C2301WPRU

Бренды по названию

Популярные бренды