JVC SuperLoLux TK-C2301WPRU Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 64

background image

2

Mount the dome cover

①

Clean the dust and dirt on the dome cover.

②

Align the position marks (3 locations) on the camera unit and

dome cover, followed by pressing in directly to mount the cover.

③

Tighten the dome cover fastening screw.

.

Dome cover protective sheet

Dome cover

Position alignment
mark (x3)

Note

v

Ensure that the silica gel (provided) has been inserted

before mounting the dome cover.

v

Be sure to secure the dome cover firmly. If it is not firmly

secured, the cover can drop or the humidity inside the

camera can increase and fog up the interior of the cover.

v

When the cover is removed again after mounting the dome

cover, the field angle may changed. If the field angle is

changed, re-adjust the focus and the field angle.

v

Ensure that the fall prevention wire of the dome cover is not

caught between the dome cover and the base. Failure to do

so may prevent the dustproof and rainproof functions from

working properly.

Installation

E-29

«
...
27
28
29
30
31
...
»

Содержание SuperLoLux TK-C2301WPRU

































































Отзывы:

Нет отзывов

Похожие инструкции для SuperLoLux TK-C2301WPRU

Бренд: NA-DE Страницы: 2

Бренд: NA-DE Страницы: 5

Бренд: NA-DE Страницы: 5

Бренд: NA-DE Страницы: 2

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 9

Бренд: Paradox Страницы: 35

Бренд: V-TAC Страницы: 97

Бренд: V-TAC Страницы: 14

D-AIR STREET SMART CHEST Series

Бренд: DAINESE Страницы: 188

Бренд: Aurora Страницы: 2

WDEM-7680LPDN-IO

Бренд: Okina Страницы: 36

Бренд: Young Shin Electronics Страницы: 10

Бренд: BUCKINGHAM MFG Страницы: 5

BugHunter Professional BH-03 Expert

Бренд: i4Technology Страницы: 25

Бренд: Vivotek Страницы: 91

Бренд: dallmeier Страницы: 104

Бренд: OEM Optical Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды