JVC LT-Z26SX4B Скачать руководство пользователя страница 8

Страница: 8 / 50

Setting up your TV

ENGLISH

LT-Z32/26SX4B/S / LCT1732-002A / English

Connecting the aerial and

video cassette recorder (VCR)

Caution

• Turn off all the equipment including the

TV before connecting anything.

• Aerial cable is not supplied. Use a good

quality 75-ohm coaxial cable.

• Read the manual that came with the VCR

before connecting.

If not connecting a VCR (follow

Connect an aerial cable to the aerial

socket on this TV.
If connecting a VCR:
1 Connect the aerial cable to the

aerial input socket on the VCR, and

connect the VCR and TV with

another aerial cable

2 Connect the VCR’s VIDEO OUT

(video output) terminal and the

TV’s VIDEO terminal with a video

cable

To connect a VCR to the TV with an S-
VIDEO cable:
Connect the VCR’s S-VIDEO OUT (S-
VIDEO output) terminal and TV’s S

VIDEO terminal with an S-VIDEO cable

, instead of connecting with a video

cable.

Note that the connection with a video
cable will be ignored in case you connect
a VCR to the TV with both video cable

and S-VIDEO cable.

3 Connect the VCR’s VIDEO OUT

(audio L/R output) terminals and

the TV’s AUDIO terminals with an

audio cable

• To connect additional external devices,

please see “Connecting external
equipment” on page 41.

without terminal covers

LT-Z32&26SX4BS_Eng.book Page 7 Monday, September 6, 2004 10:30 AM

Содержание LT-Z26SX4B



















































Результаты поиска

Содержание LT-Z26SX4B

Отзывы:

Похожие инструкции для LT-Z26SX4B

Бренды по названию

Популярные бренды

JVC LT-Z26SX4B, Инструкция по эксплуатации

Результаты поиска

Содержание LT-Z26SX4B

Отзывы:

Похожие инструкции для LT-Z26SX4B

Бренды по названию

Популярные бренды