1
53 mm
184 mm
KD-SV2800
Installation/Connection Manual
• This unit is designed to operate only on 12 V DC,
NEGATIVE ground electrical systems.
INSTALLATION
(IN-DASH MOUNTING)
•
The following illustration shows a typical installation.
However, you should make adjustments
corresponding to your specific car. If you have any
questions or require information regarding
installation kits, consult your JVC car audio dealer
or a company supplying kits.
0403MNMMDWJEIN
EN
3
LVT1076-002A
[U]
1
Control panel
Trim plate
8
9
2
Handle
Fuse
Slot
Sleeve
Lock Plate
Control panel
Trim plate
Mounting bolt
7
Sleeve
Dashboard
Rubber cushion
5
4
J
V
C
4
*
6
See “ELECTRICAL
CONNECTIONS.”
Parts list for installation and
connection
The following parts are provided with this unit.
After checking them, please set them correctly.
Handles
Hard case/Control panel
Sleeve
Trim plate
Power cord
Lock nut (M5)
Washer (ø5)
Rubber cushion
Mounting bolt
(M5 x 20 mm)
Remote controller
Battery
• When using the optional stay
Sleeve
Washer
Fire wall
Mounting bolt
Stay (option)
Lock nut
Screw (option)
Dashboard
• When installing the unit without using the sleeve
In a Toyota for example, first remove the car radio and install the unit in its place.
Note:
When installing the unit on the mounting brackets, make sure to use the
8 mm-long screws. If longer screws are used, they could damage the unit.
Flat type screws
(M5 x 8 mm)*
Bracket*
* Not included with this unit.
Flat type screws
(M5 x 8 mm)*
Bracket*
3
2
Removing the unit
• Before removing the unit, release
the rear section.
1
Remove the control panel.
2
Remove the trim plate.
3
Insert the 2 handles into the
slots, as shown. Then, while
gently pulling the handles away
from each other, slide out the
unit.
(Be sure to keep the
handles after installing it.)
1
Control panel
Trim plate
Handle
TROUBLESHOOTING
•
The fuse blows.
* Are the red and black leads connected correctly?
•
Power cannot be turned on.
* Is the yellow lead connected?
•
No sound from the speakers.
* Is the speaker output lead short-circuited?
•
Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded
in common?
•
Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded
in common?
VIDEO CD
PBC
ENTER
CD
EQ
FM/AM
VOL
DOWN
UP
ATT
OSD
AUDIO
1
2
3
4
5
6
7
8
0
9
RETURN
1
Before mounting:
Press
(control panel
release button) to detach the control panel if
already attached.
* When shipped from the factory, the control
panel is packed in the hard case.
2
Remove the trim plate.
3
Remove the sleeve after disengaging the sleeve
locks.
1
Stand the unit.
Note:
When you stand the unit, be careful
not to damage the fuse on the rear.
2
Insert the 2 handles between the unit and the
sleeve, as illustrated, to disengage the sleeve
locks.
3
Remove the sleeve.
Note:
Be sure to keep the handles for future
use after installing the unit.
4
Install the sleeve into the dashboard.
* After the sleeve is correctly installed into the
dashboard, bend the appropriate tabs to hold
the sleeve firmly in place, as illustrated.
5
Fix the mounting bolt to the rear of the unit’s
body and place the rubber cushion over the end
of the bolt.
6
Do the required electrical connections.
7
Slide the unit into the sleeve until it is locked.
8
Attach the trim plate.
9
Attach the control panel.
Crimp Connector
Less than 30°
Install the unit at an angle of less than 30°
Instal_KD_SV2800[U].p65
03.4.2, 6:40 PM
1
