background image

KD-G724

Installation/Connection Manual

1205DTSMDTJEIN
EN

1

This unit is designed to operate on 

12 V DC, NEGATIVE ground electrical systems

. If your vehicle does 

not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.

J

Handles

F

Washer (ø5)

G

Lock nut (M5)

H

Mounting bolt (M5 

×

 20 mm)

I

Rubber cushion

A

 / 

B

Hard case/Control panel

C

Sleeve

D

Trim plate

E

Power cord

Parts list for installation and connection

The following parts are provided for this unit. If any item is missing, consult your JVC car audio 
dealer immediately.

K

Remote controller

L

Battery

Do the required electrical 
connections.

*

1

 

When you stand the unit, 
be careful not to damage the 
fuse on the rear.

Bend the appropriate tabs 
to hold the sleeve firmly in 
place.

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require information 
regarding installation kits, consult your JVC car audio dealers or a company supplying kits.
•  If you are not sure how to install this unit correctly, have it installed by a qualified technician.

Removing the unit

Before removing the unit, release the rear section.

Insert the two handles, then pull them as 
illustrated so that the unit can be removed.

GET0356-002A

[UI]

When installing the unit without 
using the sleeve 

In a Toyota car for example, first remove the car radio 
and install the unit in its place.

When using the optional stay

Note  :

  When installing the unit on the mounting 

bracket, make sure to use the 8 mm-long 
screws. If longer screws are used, they could 
damage the unit.

*

2

 Not supplied for this unit.

Screw (option)

Stay (option)

Fire wall

Dashboard

Install the unit at an 
angle of less than 
30˚.

TROUBLESHOOTING

•  The fuse blows.

*

  Are the red and black leads connected correctly?

•  Power cannot be turned on.

*

  Is the yellow lead connected?

•  No sound from the speakers.

*

  Is the speaker output lead short-circuited?

•  Sound is distorted.

*

  Is the speaker output lead grounded?

*

  Are the “–” terminals of L and R speakers grounded in common?

•  Noise interfere with sounds.

*

  Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

•  This unit becomes hot.

*

  Is the speaker output lead grounded?

*

  Are the “–” terminals of L and R speakers grounded in common?

•  This unit does not work at all.

*

  Have you reset your unit?

Bracket

*

2

Pocket

Flat type screws 
(M5 

×

 8 mm)

*

2

Bracket

*

2

WARNINGS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all 
electrical connections before installing the unit.

•  Be sure to ground this unit to the car’s chassis again after installation.

Notes:

•  Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio 

dealers.

•  It is recommended to connect to the speakers with maximum power of more than 50 W (both at 

the rear and at the front, with an impedance of 

 to 8 

). If the maximum power is less than 

50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 14 of the 
INSTRUCTIONS).

•  To prevent short-circuit, cover the terminals of the UNUSED leads with 

insulating tape.

•  The heat sink becomes very hot after use. Be careful not to touch it 

when removing this unit.

PRECAUTIONS on power supply and speaker connections:

•  DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit 

will be seriously damaged.

•  BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in 

your car.

© 2005 Victor Company of Japan, Limited

Flat type screws 
(M5 

×

 8 mm)

*

2

Heat sink

Install_KD-G724[UI]f.indd   1

Install_KD-G724[UI]f.indd   1

12/13/05   6:23:27 PM

12/13/05   6:23:27 PM

Отзывы: