background image

1

KD-G634

Installation/Connection Manual

GET0422-002A

[UI]

1106DTSMDTJEIN

EN

This unit is designed to operate on 

12 V DC, NEGATIVE ground electrical systems

. If your vehicle does 

not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.

© 2006 Victor Company of Japan, Limited

When installing the unit 
without using the sleeve

In a Toyota car for example, first remove the 
car radio and install the unit in its place.

When using the optional stay

Note :

  When installing the unit on the 

mounting bracket, make sure to use 
the 8 mm-long screws. If longer screws 
are used, they could damage the unit.

Flat type screws 
(M5 

×

 8 mm)

*

2

Pocket

Flat type screws (M5 

×

 8 mm)

*

2

Screw (option)

Stay (option)

Fire wall

Dashboard

Install the unit at an 
angle of less than 30˚.

Bracket

*

2

Removing the unit

Before removing the unit, release the rear section.

Insert the two handles, then pull them as 
illustrated so that the unit can be removed.

J

Handles

F

Washer (ø5)

G

Lock nut (M5)

H

Mounting bolt (M5 

×

 20 mm)

I

Rubber cushion

A

 / 

B

Hard case/Control panel

C

Sleeve

D

Trim plate

E

Power cord

WARNINGS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all 
electrical connections before installing the unit.

  Be sure to ground this unit to the car’s chassis again after installation.

Notes:

•  Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio 

dealer.

•  It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear 

and at the front, with an impedance of 

 to 8 

). If the maximum power is less than 50 W, change 

“AMP GAIN” setting to prevent the speakers from being 
damaged (see page 13 of the INSTRUCTIONS).

•  To prevent short-circuit, cover the terminals of the UNUSED 

leads with insulating tape.

•  The heat sink becomes very hot after use. Be careful not to 

touch it when removing this unit.

Heat sink

Do the required electrical connections.

Bend the appropriate tabs to hold 
the sleeve firmly in place.

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require information 
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
•  If you are not sure how to install this unit correctly, have it installed by a qualified technician.

PRECAUTIONS on power supply and speaker connections:

  DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit 

will be seriously damaged.

•  BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in 

your car.

Bracket

*

2

L

Battery

TROUBLESHOOTING

  The fuse blows.

*

  Are the red and black leads connected correctly?

  Power cannot be turned on.

*

  Is the yellow lead connected?

  No sound from the speakers.

*

  Is the speaker output lead short-circuited?

  Sound is distorted.

*

  Is the speaker output lead grounded?

*

  Are the “–” terminals of L and R speakers grounded in common?

  Noise interfere with sounds.

*

  Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

  This unit becomes hot.

*

  Is the speaker output lead grounded?

*

  Are the “–” terminals of L and R speakers grounded in common?

  This unit does not work at all.

*

  Have you reset your unit?

*

1

 

When you stand the unit, be careful not to damage the fuse on the rear.

*

2

  Not supplied for this unit.

Parts list for installation and connection

The following parts are provided for this unit. If any item is missing, consult your JVC car audio dealer 
immediately.

K

Remote controller

Instal1-2_KD-G634[UI]_pre.indd   1

Instal1-2_KD-G634[UI]_pre.indd   1

11/22/06   5:24:41 PM

11/22/06   5:24:41 PM

Отзывы: